Oldest posts shown first (Show Newest First) | (Print Booklet) |
๐ฌ Re: Graupner Adolph Bermpohl
1 year ago by ๐ง๐ช hermank ( Captain)
โง 23 Views ยท 1 Like
Flag
|
Login To
Remove Ads ๐ฌ Re: Graupner Adolph Bermpohl
1 year ago by ๐ง๐ช hermank ( Captain)
โง 23 Views ยท 1 Like
Flag
The System that is offered by the german company is much simplyer and easyer to Control
Jt-yachtmodelle.de Up to you sailors ▲
โฉโฉ
Colin H
|
๐ฌ Re: Graupner Adolph Bermpohl
1 year ago by ๐ฌ๐ง HAKits ( Petty Officer 1st Class)
โง 51 Views ยท 1 Like
Flag
|
๐ฌ Re: Graupner Adolph Bermpohl
1 year ago by ๐ฌ๐ง Les-H ( Petty Officer 2nd Class)
โง 23 Views ยท 1 Like
Flag
Thank you for all of the your wisdom and tips, I will get a retract servo and a snake and give it a try.
Will post some photos when I get them fitted. ▲
โฉโฉ
Colin H
|
๐ฌ Re: Graupner Adolph Bermpohl
1 year ago by ๐ฌ๐ง deepriverman ( Master Seaman)
โง 24 Views ยท 1 Like
Flag
Hi Les, had same problem with mine put the back down and model floats higher in water , ended up drilling two 6 mm holes in bottom of door and again two 6 mm holes in bulkhead of door close to deck level near hull to deck join solved problem as lets water in and air out, also use nylon snake on aircraft retract servo , needs servo slower fitting as when it goes down it slows the boat like an air brake . The push out mech as graupner intended but where the end pushes vegasak out had to triangulate with bit of brass rod soldered across to stiffen to stop vegasak shaking its way off also adds to smother recovery . Did display 2016 or 17 at Warwick show several times model was and still is being refitted. Have seen a trolly system working and seems the answer , until you try it of course . Good luck with refit . When working as it should its a real buzz as friend can drive Vegasak , not as easy as it looks , trust me .
▲
โฉโฉ
Colin H
|
๐ฌ Re: Graupner Adolph Bermpohl
1 year ago by ๐ง๐ช hermank ( Captain)
โง 47 Views ยท 2 Likes
Flag
I have built the model years ago when Graupner brought it onto the market. I know that then the system to push the rescue boat into the water and to pull it back into the mother ship caused quite some โthinkingโ. Actually thereโs another and far better solution on the market. The German manufacturer
JT- yachting is bringing a system on the market which is much simplyer and operated with a winch servo. It cost z as round 100 euro. I bought the system to buit in into the Harro Koebke also with a small rescue boat If you want more info let me know Enjoy the building ▲
โฉโฉ
Peejay
Colin H
|
๐ฌ Re: Graupner Adolph Bermpohl
1 year ago by ๐ฌ๐ง HAKits ( Petty Officer 1st Class)
โง 76 Views ยท 3 Likes
Flag
Hello, I am refurbishing one at the moment and am planning on talking the mechanism out.
I am looking for a plan for the model, can you help ▲
โฉโฉ
hermank
Rookysailor
Colin H
|