|
Oldest posts shown first (Show Newest First) |
(Print Booklet) |
|
๐ Scimitar-class patrol vessel
6 years ago by
๐ฌ๐ง CB90 (
Commander)
Flag
Two vessel in it class
(1) HMS Scimitar
(2) HMS Sabre
Launched: December 1992
Displacement: 24,000ย kg
Builder: Portsmouth
Armament: 2 ร General purpose machine guns (stern-mounted)
Complement: 7 (1 officer, 6 ratings)
Gibraltar Squadron's two Scimitar-class boats are the smallest commissioned vessels in the Royal Navy.
This build was to produce a fun semi scale racing boat, I have always liked the Archer class boats cabin design. So after finding a suitable hull, an old 'Models by Design' GRP moulding I was away with the rest of the build.
Striped out all old fittings and remnants removed excess glue.
Added strakes to the hull to add lift for planning and control.
Produced a semi scale deck and cabin from light ply.
Thanks for your interest
Roy
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Did a bit more
6 years ago by
๐ฌ๐ง CB90 (
Commander)
Flag
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Prime and sand
6 years ago by
๐ฌ๐ง CB90 (
Commander)
Flag
Primed with white primer and will sand most of this away again.
Please note boat is for semi-scale racing.
the bow strakes have been reduced as per the real boat bow and perhaps allowing for some shark teeth details to be add as per one of the two original boats P285
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Make a little more scale like.
6 years ago by
๐ฌ๐ง CB90 (
Commander)
Flag
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Painted outside
6 years ago by
๐ฌ๐ง CB90 (
Commander)
Flag
Finish painting and adding some stickers, and a couple of pictures of the real thing.
Fitted Motor in a water cooled jacket and motor mount.
The motor is a 3650 and is rated as 3060kv Max Power: 1300W
Max Voltage: 19V
Max Amps: 68A
Shaft Diameter: 3.2mm
Shaft Length: 15mm
Connector: 5.0mm Banana Connector
Net Weight: 181g
Servo fitted sideways via rubber bellows to external rudder fixed to transom.
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Added ESC
6 years ago by
๐ฌ๐ง CB90 (
Commander)
Flag
Added a 60A ESC of Chinese origin, improved waterproofing, and modified the rudder water pickup.
Repainted trim tab extension as while it sat in the test tank (AKA the bath) the water got into the wood and split the paint work car spray paint not as water proof as I had hoped.
On the test I found it was pulling over 40Amps which is not what I want as this is a race boat with limited battery capacity
so cut down propeller by filling of the lagging edge of the prop via a drimmel and a file, so now pulls under 30A at full throttle.
At the pond I will check current and prop-sizes.
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Change motor
6 years ago by
๐ฌ๐ง CB90 (
Commander)
Flag
Changed motor to a lighter out-runner with same shaft dimensions.
Specification:
Kv: 3700KV
Max current: 32Amps
Max Power: 330watts
idle current: 3.6Amps
Resistance: 0.0185ฮฉ
Shaft: 3.175mm
Weight: 75g
Suggested ESC: 40A
Cell count: 2-4s Lipoly (Voltage)
Bolt holes spacing: 16mm
Bolt thread: M2.5/M3
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received