Our Ben Fishing Boat

Started by GrahamP74

12 updates 39 likes 17 comments

Finished (for the second time)

Completed the paint today, happy with the level of distress!
Liked by jbkiwi and MouldBuilder and
7 comments
  1. MouldBuilder
    Admiral
    Brixham is just around the corner from me. Your weathering looks spot on to me. I have seen much worse as well. Don`t know how they go to sea on some of them.
    Liked by GrahamP74

Sign in to comment on this update.

Finally painting!

So I managed to break my leg in October which put pay to finishing the painting.

Managed to start it today - white water line to do!
Liked by Martin555 and MouldBuilder
3 comments
  1. GrahamP74
    Sub-Lieutenant
    Well it’s certainly stronger! Now sponsored by Mecanno! Just having to build the muscles up again!
    Liked by Martin555
  2. Martin555
    Fleet Admiral
    OUCH!!!
    I bet that hurt!
    It is amazing what can be done nowadays, the surgeon/mechanic did a great job.
    I am glad you are on the mend.

    Martin555.

Sign in to comment on this update.

Disaster on the bench!

I decided to take Our Ben out to the bench to have a small paint up, however due to an accident several rather large boxes fell and caused her to end up in the floor! Hull is fortunately intact. I have seen this as an opportunity to resite the wheelhouse to one side to allow more deck space. Some of the capping had also broken so I have re applied using resin and tissue. This has given it much more strength.
Now I can paint her! Photos to follow!!
Liked by mturpin013 and Martin555

Sign in to comment on this update.

Net bins

The boat is nearly complete now, the final part is to fill the deck with fill nets! I have found that the Heinz snap pots for baked beans are the perfect size! Top removed, sprayed and weathered and then a body buff has been cut up and stuck inside along with some twine. I’ve then painted the net to make it look dirty and some varnish to give it a wet look.. 2 down 1 more full one required and then a stack of 3 empties... but first dinner, and yes, it’s beans on toast for me!!!
Liked by jbkiwi and Colin H and
2 comments
  1. Escrich
    Petty Officer 2nd Class
    You must enhance the transmission, cable junction you’re using will always give problems to you
    Liked by Inkoust
  2. GrahamP74
    Sub-Lieutenant
    Thanks I am having a new coupling made.. the cable junction was to check everything runs.. it actually works quite well!!

Sign in to comment on this update.

Taking shape!

Managed to fit the gantry and mast and made the sail.
To get the right cloth I used and old pillowcase (well I think it was old) and painted it both sides with wood stain / varnish. Happy with the finish.
As with all my models I always put a piece that my Dad made on the boat, this time it is the wooden pulley block.
Liked by jbkiwi and Colin H and
1 comment

Sign in to comment on this update.

Deck on!

Finished fitting the deck today. Also fitted the pot and net hauler. Wheel house is positioned but not stuck.
Pleased with the deck and although there is now a raised hatch this is more in keeping with how the boat would be..
Liked by jbkiwi and Colin H and

Sign in to comment on this update.

Ben, meet 'Our Ben'!

Ben came round yesterday and I showed him the new model! To say he was excited is an understatement! Uncle Graham will have to get a wriggle on! A little bit of time spent lat night planning out the boards for the deck.
Liked by Peejay and RNinMunich

Sign in to comment on this update.

New wheelhouse

New wheelhouse made, additional detail to be added
Liked by Colin H and Peejay
2 comments
  1. GrahamP74
    Sub-Lieutenant
    I did the drawings myself based off some local boats and then scaled to 16th. I use craft board which is easy to cut and stick and bend.
    Liked by figtree7nts

Sign in to comment on this update.

Delete this post?

It will be removed from the site.

Discard this draft?

Your draft will be deleted and cannot be recovered.

You have an unfinished draft

What would you like to do with it?