Oldest posts shown first (Show Newest First) | (Print Booklet) |
๐ฌ Re: Newbe Pilot Build
4 years ago by ๐ญ๐บ MouldBuilder ( Vice Admiral)
โง 6 Views ยท 0 Likes
Flag
I made this kit last year. Most of the joints were glued with Expo super glue, the runny one, and Stabilit Express for the water tight areas. Nothing has give way yet even with a trip in a box to Hungary.
Peter. ▲
โฉโฉ
No likes yet
This member will receive 1 point for every like received |
Login To
Remove Ads ๐ฌ Re: Newbe Pilot Build
4 years ago by ๐ฌ๐ง Skydive130 ( Rear Admiral)
โง 7 Views ยท 1 Like
Flag
Hi there, photos speak volumes, would love to see this build as I considered this kit and rejected it when it arrived because of the abs plastic!
▲
โฉโฉ
Martin555
|
๐ฌ Re: Newbe Pilot Build
4 years ago by ๐ฌ๐ง Martin555 ( Fleet Admiral)
โง 9 Views ยท 3 Likes
Flag
Hi Highwayman,
Do you have any photos that you could show us of your progress so far.? Martin555. ▲
โฉโฉ
MouldBuilder
Skydive130
RonH
|
๐ฌ Re: Newbie Pilot
4 years ago by ๐ฌ๐ง Martin555 ( Fleet Admiral)
โง 7 Views ยท 1 Like
Flag
Coming along nicely.
well done. Keep up the good work. Martin555. ▲
โฉโฉ
Skydive130
|
๐ฌ Re: Pilot build
4 years ago by ๐ฉ๐ช Dampfgerd ( Petty Officer 2nd Class)
โง 14 Views ยท 1 Like
Flag
|
Login To
Remove Ads ๐ฌ Re: Pilot build
4 years ago by ๐ญ๐บ MouldBuilder ( Vice Admiral)
โง 8 Views ยท 1 Like
Flag
Looking good.
▲
โฉโฉ
Martin555
|
๐ฌ Re: Pilot build
4 years ago by ๐ฌ๐ง Martin555 ( Fleet Admiral)
โง 8 Views ยท 1 Like
Flag
I have used ladies clear nail varnish.
Soak a bit of plastic in it for a short time and then it goes very soft and you can easily scrape of the plastic and use it as a filler. Martin555. ▲
โฉโฉ
Ronald
|
๐ฌ Re: Pilot build
4 years ago by ๐ฌ๐ง highwayman ( Leading Seaman)
โง 8 Views ยท 1 Like
Flag
Thanks for the reminder. I forgot the qualities of Acetone.
▲
โฉโฉ
Martin555
|
๐ฌ Re: Pilot build
4 years ago by ๐ณ๐ฟ jbkiwi ( Fleet Admiral)
โง 12 Views ยท 5 Likes
Flag
Try using a small (like 3mm) artists brush and Acetone to glue it. I built a lot of early Graupner ABS boat kits (and an ABS trainer plane with ABS covered foam wings and fuselage) and that was the recommended method. Just don't let it run down the outside as it will spoil the gloss. Your pipe solvent is probably Acetone based which might be why it works. I have used the solvent pictured also (UPVC gutter/spouting solvent). Try using the Acetone on some scrap ABS or somewhere inconspicuous,- parts should fit closely,-just run a drop of Acetone down the joint, hold it in place for 30 secs and see if it sticks. My Graupner Optimist yacht is still together after 42 years,- put together with Acetone and epoxy. ABS is easy to fix if you have scraps left over,- just make a paste of ABS and Acetone and use it to glue cracks etc. If you have scraps left over from trimming etc, keep them.
JB ▲
โฉโฉ
RNinMunich
Ronald
MouldBuilder
Joe727
Martin555
|
๐ฌ Re: Pilot build
4 years ago by ๐ฌ๐ง Martin555 ( Fleet Admiral)
โง 8 Views ยท 1 Like
Flag
For your first build in a long time you have done a good job.
Well done. You should post your Pilot boat in your Harbour with a little more information about it. Martin555. ▲
โฉโฉ
MouldBuilder
|