Search
3,152 posts for “brushless”
Page 2 of 113
Forum
Brushed to Brushless upgrade
?????????????????
Forum
Darby One Design hydro...
… re it started peeing down, so no Chris-Craft pics. Fitted a brushless outrunner I found in a box. Might work, might not... Home made prop shaft/tube, home made off-set rudder. Planked balsa top cover to keep weight down. 1/6th scale 26"long …
Forum
Programming a seaking brushless ESC challenges..
… i, now having trouble programming the Seaking hobbywing 60A brushless ESC that came with the boat, it’s running in forward only mode and I can’t change it. Followed the instructions I found online but it won’t stay in forward/reverse mode.. …
Forum
Large lipo
… making a 1m long power boat which will be driven by a large brushless motor and a big lipo battery. The motor is is a 4240- 740, and the battery a 5 cell, 5000mAh. This is the first time I have used a large brushless and a big lipo, and I w …
Forum
MANUFACTURERS AND SELLERS OF NAUTICAL PROPELLERS FOR RC MODEL BUILDING (USEFUL LINKS FROM ALL OVER T
… fessional rc hobby manufactory, mainly producing multi-pole brushless motors and racing boats. They have ability to design, develop and produce motors. I think they are Chinese from Guangzhou (near Honk Hong) but the pieces are not cheap. T …
Blog
Billings Banckert
… rks perfectly. Power is being handled by a HobbyWing 30 amp brushless esc and a 28 mm 880kv motor. I made a ply/plastic mount out of scrap. I’ll have good access to the motor, tiller, and electronics, the servo will likely be a little hard …
Forum
Shark speed controllers
… y experiences, good or bad with Shark speed controllers for brushless motor. I have recently purchased one with a Overlander thumper V3 and nothing happens at all, no beeps nor nothing! It powers up the Rx and drives the servos but no respo …
Forum
RAF Crash Tender Motor size
HI Folks Can anyone see a problem using a brushless 3530 1100 motor In a 34" RAF Crash tender running a 3s lipo pack regards emma
Forum
St.Pierre Dory build underway
… for placing the small NiHm 1200 battery pack. I do not use brushless motors or Lipo batteries. I will remove the added cabin and roof extension.
Forum
Slec Huntsman (Star)
… ted .. new for me was the electrics fist boat for me that's Brushless and lipo but advice from this site has helped .I will upload a vid when I take her for a run
Forum
Using old motors
… ducks here, just fastish. PLEASE don't suggest I buy modern brushless stuff. I'm just not into all that. BUT, is there any newer thinking about speed control and reversing of the old Taycols, Frogs, Basset-Lowkes and SELs? I do posses one m …
Forum
Heellllp!!!
… a trade, fixed up then traded it to him, and he then added brushless power and has ran the fire out of it for 2 years straight. Anyway, about a year or so ago I found a link to a gentleman in Germany who was making new Kitty hulls from abs …
Forum
72" 6S Brushless Power
… hout trouble. Regards, Dean PS. Have found a nice ESC: 125A Brushless Water Cooling Electric Speed Controller ESC 5V/5A SBEC This comes in at £41 the pair including postage. £100 left in the budget folks!!!
Forum
Brushed or Brushless Motors
I am fairly new to this hobby what are the pro and con of brushless motors over brushed
Forum
Brushless motor problem
Just purchased two A 2212 brushless motors and can't get either one of them to run. I've tried both of them and all I get is three beeps when powering up and then constant beeping from the motor. I checked all the connections and a servo pl …
Forum
Help Please
… appreciated boat specs below. Perkasa 49" MTB Leopard 4074 brushless motor water cooled Tinergy 120A ESC water cooled 35 prop 2 x 500 4S lipos wired in parallel Mtroniks digisound sound module on separate MiNI 7.2v battery Spektrum DX2E ra …
Forum
ESC Wiring (Turnigy)
… f the issues raised by my wheelbarrow test was that neither brushless motor would run smoothly. Decided to investigate as one ESC wire had also pulled out of the pin. Determined on these ESCs, that all the wires going into the plugs are jus …
Forum
Can anyone help please?
… 50 G2 speed controller to the receiver, then connected the brushless motor and lipo battery, all correct colour to colour as I have done several times before, turned on the transmitter then the speed controller and the speed controller wen …
Forum
PCF (Patrol Craft Fast) SWIFT Boat Vietnam Era
… ain, 100% direct drive, ball raced, water cooled twin screw brushless outrunners. You cannot buy something like this. The glass fibre hull is complemented for strength and lightness with plastic and ply wheelhouse and cabins etc. Lets get t …
Blog
Hallet SK Drag boat
… t work. Working in 1/6 scale. I sourced a Hemi engine. 4074 brushless 6s setup? Thanks to all on this site for being friendly and helpful. I really love the diverse subjects. Thanks, Dave (RR)
Forum
Slec Fairey Huntress
… f a 600 type brushed motor and nimh battery rather than the brushless and lipo route? Thanks
Forum
Brushless motor couling
… w having a bit of time on my hands, I have just received my brushless outrunner motor. My question is do i use the plain motor shaft that comes out of one end of the motor or what I guess is the alloy device for mounting a prop on an aircra …
Blog
HMT Resolve by Caldercraft
… complicated, so I decided on electric. Recommended were 900 brushless motors which are very big lumps. Consultation with Jotika resulted in 540 2.5:1 geared motors which had the added advantage of lower shafts, making it easier to connect t …
Forum
Tug towing
Can anyone recommend a good brushless motor and esc for tug towing please?
Forum
ESC info...
… a cuppa and I see this ESC:-https://www.ebay.co.uk/itm/60A-Brushless-Water-Cooling-Electric-Speed-Controller-ESC-BEC-RC-Boat-X5I6-SR/323323256487?epid=2070109255&hash=item4b47915ea7:g:bSkAAOSwIrVbNjH~ It appears to be programmable, but how …
Forum
Brushless Motors
… eplacing a set of two MFA 500 torpedo motors In my tug with brushless motors, having no experience with brushless motors, Is there a rule of thumb that requires to be applied In calculating the appropriate replacements & speed controllers, …
Forum
Mixer connections
Hi, bought two of these for my RC shark, I need to mix two brushless motors and two servos. They don’t have wiring diagrams any suggestions as to how to wire them up please? I’ll be using a Futaba 6EX-PCM 1024 as it’ll be under water (hopef …
Forum
suitable brushless motor for a tug ?
… aces about 3kg. I'm trying to find a low-torque, high power brushless motor for it, preferably But not necessarily) from North America. Any suggestions on product or sources would be greatly appreciated.