All donations are securely managed through PayPal. Amounts donated are not published online.
Many thanks for your kind support.
Model Boats Website Team
January 2019: 13 people December 2018: 6 people November 2018: 11 people October 2018: 9 people September 2018: 13 people August 2018: 5 people July 2018: 8 people June 2018: 8 people May 2018: 7 people April 2018: 20 people
That's a really good question that I really can't answer right now as I've yet to run the boat !. The motor enclosure does have quite large ventilation panels on either side which are covered in a mesh and I'm hoping that the motor will be able to 'breathe' as a result. The brushless in my Fire Boat doesn't even get warm after a long hard run and that's enclosed in the hull but has admittedly got a lot more free air around it in the motor compartment. This is not a racing boat remember, so I'll not be using the motor to it's full ability, scale speed is all I really want and expect. I'll report back when it's had some sea trials 😁 Robbob.
Chris, Thank for the information, I will look into that book. I started in RC Boating but building and racing several classes of sailboats, including several US1Meter class. Being a much better builder than skipper, I was drawn to schooners that many club members had. Got interested in working sailcraft due to the history and the slower, power of these craft. The Gaff Rigged Handbook by Jihn Leather is one of my favorite build guides. Yes, I really like Gaff Rigging. This book was great for lots of rigging details and sails... See photo example. Joe
".. Worked through the instructions and it made beeping and squawking noises in what seemed the right places but still no reverse. The increase in revs does now cover the whole of the stick travel above the mid point so I has changed something. Lost the will to live after 2 hours so went and worked on something else. Steve..." Just a thought - may not be applicable, but we often share our reversible ESCs with the car fraternity. And some of them have an odd reverse. For some cars, you may be happy with straight forward and reverse, but for racing this is not ideal. Dropping into reverse if you move the stick/trigger back past neutral would make the car uncontrollable on a corner. Instead, the racing car boys have a system whereby the forward stick increases speed, while 'reverse' performs dynamic braking by shorting the motor terminals (or perhaps even regenerative braking!). To a boaty, this would seem as if the forward stick worked, while reverse did nothing. These racing car ESC programs DO allow a proper reverse. The way you usually get to it is to bring the stick back to reverse, then forward to neutral, then back to reverse again. It's a two-stage process - call for reverse twice. If you go into reverse, then forward, then back again you won't get reverse - it has to be reverse, neutral, reverse. Which is fine if you are manoeuvring a car into a parking space, but rather clumsy for a boat....
[Score: 8/10] 18"/500g skytech H101 Capable of 0mph and a runtime of 15mins Single Propellor (3 Blade 20mm) Direct Drive to a 380 water cooled (3 Blade) Powered by LiPoly (7.4v) 1Amp/h Batteries - Comments: skytech racing boat with water cooled engine.lts capable of 18 knots ! it has a self righting function and came with a spare battery pack,prop,oil and spanner. hope to have some fun with my grandson.
[Score: 5/10] 36"/1500g Turtle Single Propellor (2 Blade X Type 45mm) Direct Drive to a O/S 40 max (2 Blade X Type) - Comments: Own design deep V racing boat built in the early 70s Fiberglass over balsa.
Thanks for the nice comment, and yes it is a very nice pond, except when there are a lot of those things with rags tied to sticks racing (shouldn't say that as I've sailed full scale all my life and still have 2 small yachts), and the buoys they leave there are a pain also, (easy to forget they are there) It was full of hire carp (yes hire carp) which were removed as the council wasn't paying the company or some such hassle, but I'm sure they missed some and they will soon multiply and keep the weed down. Bought the plans for the MTB around 1968 and took around 20yrs to finish it. I still have the plans and it only took me about 40yrs to find a photo of the original boat (bit late by then!).
Fully had made chris craft deep v racing boat evey think u.see is had made apart from engine and.the driver. She is.fully restored to her original self made in 1972. Have added a self bailing system and a new had made shaft with own greaser valve. Thanks hope u all enjoy
Dave , I made it. I found plans in a 1954 copy of the Motor Boat Annual I borrowed from the National Powerboat Museum at Pitsea, before the stupid bastards on the council threw it away in preference for mud huts for snotty nosed brats to go mad in. Only today I finally got some pictures from the Oulton Broad club with pics of the Darby boasts I hadn't seen, which show that the top cowling was always built a little higher than the plans show, so I shall be making some slight changes to the fixed portions. The photos show the fixed sections to be done with stringers and fabric, a la aeroplane fuselage. You can't buy decent older powerboats as kits or ready mades. Nobody gives a toss about speedboat models in this country, alas. Even though we had a very busy world of inboard race boats at one time. Now, all is boring outboards. The 1500 cc inboard classes gave us a lot of great racing just pre and post-War. Here are three in one race. "WHO'S DARBY?", Dawn, a Whippet class and Miss Windermere, another One design, like the Oulton Broad One design, all three are 1500 cc class boats. There wqere also boats of under 950cc and even a Singer Cadet class with a Singer Le Mans 1100 cc engine. The Singer Commodore had a 6 cylinder 1500, a gorgeous engine. Both Singers were designed by Percy See at Shoreham and had diagonal reverse clinker construction. I have plans if anyone is interested. Cheers, Martin
[Score: 9/10] 29"/1200g Avanti Capable of 15mph and a runtime of 5mins Single Propellor (2 Blade X Type 35mm) Direct Drive to a OBL29/19-15M (2 Blade X Type) Powered by LiPoly (11.1v) 15Amp/h Batteries Controlled Through BLC-40M (25Amps) ESC - Comments: ARTR fast electric by Thunder Tiger. Deep vee powered by Ripper Brushless outrunner. Will reach 30mph+ when flat out. I replaced the radio that came with the boat with stick operated Futaba T2HR as I preferred "stick" to wheel for sailing fast boats. Initial problem was slight leak where stern tube passes through the transom but soon fixed it with epoxy. Electrics are in a box at the stern which is appears to be water resistant. Though not for a raw beginner, it is great for a second boat especially if someone is hoping to move on to a 6S . If not , it makes a good all rounder and is ideal for club fast electric racing and it performs well when doing tight turns. Boaty
Just got white metal castings back of the Chris Craft fittings and very nice they are too. They have started to burnish up a treat and will polish well as Paul uses a good quality metal. Nice and hard. Now I have to make the light lenses. Also put the blue bottom on her at the weekend using my one and only pot of Plastikote enamel paint, not the acrylic muck they've turned over to and it went on through my spray gun as smooth as could be. Even my masking worked. Just waiting for a gold pin stripe tape for the boot topping now. The final bit will be masking the deck to paint the covering boards and king plank with the same blue. For those not lucky enough to have a wee pot of proper Plastikote in the paint cupboard, I also got a couple of tins of Rustoleum spray, only 5-25 a pot, enamel (of course) in a nice French blue and a rich cream. These colours will look good on my Darby One Design single stepper "WHO'S DARBY?". Very post War. I think the Oulton Broad One Design single stepper will be Burgundy and the Whippet One Design will be varnished mahogany. I know of no other classes of British stepped hydroplanes. These will all be 1/6th scale as they're all around 12-13 ft. long. I'll probably put the same motors in them eventually. The Darby is well advanced and has a Speed 400, but I may go brushless. Any suggestions for a cheap Brushless/ESC combo will be welcome for, say, 3S Li-Pos. It would be good to see these period boats all racing together. I also plan to make reverse clinker Singer cadet and a Percy See Bugatti engined boat for which I have plans. I'm hoping to get a response from the current keepers of Berylla II about measuring that, too, since it also uses a Lea Francis engine, like the Whippet.
No Martin, I don't think so. Once again; it's not so much what you say but HOW you say it. If your chat with the 'only geezer' was in the same vein as your recent posts I can fully understand that the reaction was 'don't call us - we'll call you'. Patience is NOT an excuse for wasting time. It is an essential component of successful negotiation. During my career I was often involved in systems design and contract negotiations for COMMS systems for ships yet to be ordered and built. Many of such projects took 5 to 7 years or more to come to fruition. My perseverance and patience paid off. I was the one who signed the contracts! I often heard from the shipyards and/or navies involved that they were put off by the 'pushy' tactics used by my competitors with less patience. Tolerance is also not a weakness. Lack of it IS. Differing opinions are fine, just depends how they are expressed. Denigrating and insulting others who have differing interests as morons is not the 'fine English art' ! Re: Dumbphone control Apps; YOU don't necessarily need to know (a Luddite wouldn't want to or need to anyway!) but the parents of your grand kids SHOULD in this day and age. Tell 'em to look for Apps like 'Quiet Time'. This enables them to define times that the kids can access the web online via smartphone and when it is blocked. And no, the kids can't normally get around it. If they can; leave 'em alone to make their millions! Re: Woodies; Super duper. You have seen that I have put a tremendous amount of effort into renovating the Sea Scout that my Dad built in the early sixties. I enjoyed the process and learned a lot doing it. But I am not fixed on that particular line of model boat / model ship building. If that's your only thing - fine. But why berate those of us who take a wider view and also have an interest and find challenges in making shipboard functions work in miniature in all sorts of ships? "I really couldn't give a sh*t if I was the only person left in the world making woodies. I do it for me only these days in the absence of any clubs. But I don't have to pretend to like all the other stuff. In another place are people who not only do sail, but specifically model barge racing and good on 'em. I don't ask that they do all the other stuff" No, of course you don't have to pretend to like 'all the other stuff' but you also don't have to decry those that DO like the other stuff, as you often do the tug aficionados for instance. OK, I can understand an aversion to warships as such if someone is a died in the wool pacifist, but nevertheless some appreciation of the skills involved in producing such outstanding warship models as seen on this site is not out of order, or...? (Bye the bye; I've often noticed that 'pacifists' have a particularly aggressive way of expressing themselves!?) After 30 odd years here in Germany I'm out of touch with the ground roots in UK, but over here things don't look so black. There are thriving model boat clubs all over. W.r.t. 'exciting aspects'; there are clubs in Germany, Holland and France and Italy also I think who happily and skilfully re-enact sea battles and convoy battles. There is at least one club in South England that also does that I believe, in Southampton or Portsmouth? Don't get Channel 4 here (re Battle of Britain re-run you mentioned) but I do get DMAX, which shows a series called 'Die Modellbauer'. In this the crémé de la crémé of German model making is depicted and judged for the annual cup at the International Model Show here. It covers everything from fire trucks, excavators, boats and ships of all kinds, and aircraft of of all types including turbine jets. Criteria for the competition being: 1) Shall be externally identical to the original in every detail (down to the rivets!)l, 2) Shall be able to perform each and every function of the original. 3) 150 days to design, complete and demonstrate the model. The point being that with extremely few solo exceptions the models are almost always built by a father and son partnership. So, sorry if the situation is drastically different in UK but 'over here' it ain't so black as you paint. Maybe it's a question of the attitude of the parents? BTW: for a fantastic example of 'modelling on a mammoth scale' pop across to Hamburg and have a look at the 'Miniature Wonderland' in the old Hafen City. All 1/87 scale, the largest model railway layout in the world, but also all types of aircraft and ships in action as well. Also shown from time to time on various documentary TV channels. BTW2: don't worry about the brass bashing, I'll work it out for myself. Have fun with the Taycols. Cheers, Doug 😎
That might have been the case before the mobile phone/mini computer boom, Colin, but now they don't learn anything at school, there are no clubs at school and all they want is 'phone games/youtubes of other nerds playing games better than them (yes really!!). They simply cannot see any pleasure or fulfillment in making something and let's face it, apart from racing yachts and very fast raceboats, model boat operation will bore the best of us after 5 minutes! Going round and round with a coaster is limited to say the least. I get my pleasure from making them and almost none from playing with them. Try offering that as an argument to a kid who loves Fortnight or Minecraft. You haven't a chance! Model aircraft or car racing will always take them if there's a hint of interest as those are more exciting, if expensive. Martin
Hi Mzee Re hovercraft, it may be worth looking at information around models by the late Ray Malmstrom. He was an ace when it came to designing unorthodox models and another source would be the Plans Handboook. I remember this in the mid 1960s and there was plenty to choose from as they had a special section on such. This included anything from hydroplanes, prop driven racing cars and hydrofoils etc. Another source could be the Eagle Annual from around the same period. Though the Eagle was a comic, the Annual did have articles around the latest technology of the day. Even if you could not obtain the Annual itself I am sure there would be archives on the Internet. Hope you have success with your venture, it sounds exciting. Boaty😁😎