All donations are securely managed through PayPal. Amounts donated are not published online.
Many thanks for your kind support.
Model Boats Website Team
October 2018: 5 people September 2018: 13 people August 2018: 5 people July 2018: 8 people June 2018: 8 people May 2018: 7 people April 2018: 24 people March 2018: 13 people February 2018: 8 people January 2018: 9 people
I acquired this boat part built some months ago through Dave M. I have not put too much scale in detail but I am quite pleased with the overall finish. It is powered by two brushless 1250KV out runners and in the first sea trials I used 12v lead acid batteries. (That video was posted a few weeks ago - mdlbt.com/26793). This video shows its second sea trial after I was persuaded to use lipos. The difference in performance is very pleasing. Thank you Dave M for your help and advice during the build.
Thank you for your compliments. This is in fact my second Perkasa. I built the first one about 40 years ago (see photo), before the introduction of the GRP hull. Losing interest in the hobby some years later, I sold the boat and have lived to regret it. (I was also the proud owner of a 37" Aerokits Crash Tender powered by a Frog 2.49cc diesel. That went the same way!) The first boat was quite lively powered by a Merco 61 i/c engine. No pictures of either I'm afraid. Hindsight is a wonderful thing. Steve
Sylt model manufactured according to plans and the hull of the original construction.
SEA JET EVOLUTION - Posted: 2 years ago by Inkoust
Master-construction water scooter from Robbe. 2 pieces brushless motor, 2 pieces brushless controller, lithium-polymer battery 5000 mA. Amazing driveability, incredibly stable rate of around 60 kilometers per hour. Battery life in full power for about 15 minutes.
Don't know how deep it is in the middle. I think there have been a couple of drownings over the years. I take a reel of fishing line with me. My plan would be to enlist some help and take the other end of the line to the other side of the lake. Lay the line over the boat. Tie a duster to the end of the line and gently pull the line over the boat. I am thinking the wet duster would grab the boat well enough to pull it in. I haven't had to try it so I just hope it works if I need to use it. I also thought about getting a 5 meter fishing pole off Ebay but didn't get around to it. But as I said most of the time the prevailing wind is towards the more accessible bits
I used to take a rescue boat with me, A small electric boat with me and I had a piece of fishing lie about 15ft long with those small bouny balls that are about an inch in diamiter threaded along it and run it round the conked out boat. The line would go under the boat and catch round the prop or rudder the drag it back to shore. The fishing rod I take now is a telescopic one with a fixed spool reel and fly fishing line that's bright yellow and it floats. Hoping to cast over top of the boat then drag it back. I was getting quite good at it. Mainly on my brothers boat. Mine was quite reliable but did conk out sometimes.
Very tidy boat and nice Captain's POV 👍 Next step cam rotation? Limit switches or servo with travel extension ? After that telemetry with video back to base ?? Some sets have a good 5.8Gig back channel for this. I recently bought the Toshiba Sport camera, with a waterproof case, so I might try it on my 107cm 1:72 Type IIA U26 ! Plug in mount instead of the 88 on the foredeck. For rescue I have the Tug Southampton, bought RTR and modified slightly so I can at least push home. Not easy with long thin ships like my destroyer so thinking of a steel plate on the bow and a neodym magnet on the tugs winch 😎
Neodym magnets are excellent for holding hatches, decks etc in place. I have just sourced a selection from ebay and bought two 10x10mm. www.web-magnets.co.uk.I had not considered using as a rescue aid but these magnets are exceptionally strong and once attached are very difficult to remove so certainly up to rescuing a model. We sail many yachts and it can be difficult to find a safe attachment without causing damage. I do hope you keep us posted on the automation of you features. On water shots are always good especially if they capture other models on the water. Dave
Facon 2 with Novarossi Mito 21M, CMB tuned pipe, tanks and running gear by Ian's Boats. First run at Brentwood lake. Running motor in on low nitro. This boat eventually won me the MPBA 2016 National Drivers Championship.