๐ Masking Tape too strong or clumsy - simple solution
3 years ago by
๐ฌ๐ง Jerry849 (
Able Seaman)
Flag
Toolstion have low tack masking tape
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Turing
4 years ago by
๐ฌ๐ง Jerry849 (
Able Seaman)
Flag
Hi Martin ,thanks for that but no its a specific one for Turnigy 120 amp marine e s c , so i am led to believe , Jev๐
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Turing
4 years ago by
๐ฌ๐ง Jerry849 (
Able Seaman)
Flag
Cheers Jonathan, was going for the easier quicker option ๐Jev
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Turing
4 years ago by
๐ฌ๐ง Jerry849 (
Able Seaman)
Flag
Can anybody enlighten me where i can purchase program card for Turnigy 120 amp marine e s c . I think i have more chance of getting rocking horse !!!t, Many thanks, Jev have found them in States but they don't post to UK๐
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ electrics
4 years ago by
๐ฌ๐ง Jerry849 (
Able Seaman)
Flag
many thanks you have been a great help so far will keep you informed ,Jerry๐
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ electrics
4 years ago by
๐ฌ๐ง Jerry849 (
Able Seaman)
Flag
its a project started many years ago but due to circumstances had to put it on hold just thought its time to fetch it back to life its the Precedentmodel of the huntsman 46 inch ply not fibreglass and i am making it twin screw instead off the kits one screw so wether it works or not we shall see but things not going to good at moment i could always sink it ๐
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ electrics
4 years ago by
๐ฌ๐ง Jerry849 (
Able Seaman)
Flag
Have twin lever DX6I ,connected up to tx on y lead one motor kicks in then add a bit more throttle and second motor kicks in tried plugging e s c to program card ,nothing so obviously got a bad one will have to try source new one but all seem to be out of stock, so things look to be on hold now ๐
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ electrics
4 years ago by
๐ฌ๐ง Jerry849 (
Able Seaman)
Flag
Hi just reading your messages again i have e s c ,s on a y lead but you say control on separate channels so one in throttle on receiver so which channel for other lead, or is this a stupid question ๐ i have disconnected red wire from one e s c so obviously will re connect this, have not read manual yet ๐
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ electrics
4 years ago by
๐ฌ๐ง Jerry849 (
Able Seaman)
Flag
Hi all, new member,could some one enlighten me on how to set up twin e s c,s i am trying to run twin brushless motors (silver blue 3650 kv ) twin Turnigy 120 marine e s c,s twin 11.1 2800 mah lipos , have disconnected one red wire from one of e s c,s , do you program them separately or should they program together, got a hobby king program card but don't think it works, some advice would be much appreciated ๐
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received