Join Us On Social Media!
|
|
|
Download The App!
Login To
Remove Ads
Remove Ads
Login To
Remove Ads
Remove Ads
Model Boats Website
Yard Sale Find
4 Posts · 3 Followers · 9 Photos · 28 Likes
Began 7 months ago by
CanadaFollow This Thread
Not currently following
> Click to follow
> Click to follow
Latest Post 7 months ago by
| Most recent posts shown first (Show Oldest First) | (Print Booklet) |
📝 Yard Sale Find
7 months ago by 🇨🇦 GARTH (
Captain)
Captain)✧ 50 Views · 3 Likes · 1 Comment
Flag
💬 Add Comment
Made the deck out of some bass wood strips that I had cut a while back . There temporary & not glued down yet. All the electronics have also been put in & tested Rudder & speed control working fine wanted to go to the Spencer pool in Burlington but it was a little to cool today maybe tomorrow to test for leaks & balance .
▲
⟩⟩
Len1
peterd
Ronald
|
💬 Re: Yard Sale Find
7 months ago by 🇨🇦 Ronald (
 Admiral)✧ 54 Views · 1 Like
Flag
Looks fine Garth
▲
⟩⟩
Len1
|
Login To
Remove Ads
Remove Ads
📝 Yard Sale Find
7 months ago by 🇨🇦 GARTH ( Captain)
Captain)✧ 66 Views · 6 Likes
Flag
💬 Add Comment
Sealed up the stern area . Used 2 part epoxy on a table a while back & had some left that I mixed up to seal the interior so it don't leak. Epoxy can be very expensive these days.
▲
⟩⟩
peterd
hermank
Len1
MartinW
EdW
Peejay
📝 Yard Sale find
7 months ago by 🇨🇦 GARTH ( Captain)
Captain)✧ 82 Views · 7 Likes
Flag
💬 Add Comment
Installation of Motor, Prop Shaft , Stuffing box & stern cut off for prop & rudder installation. I have started to make my own prop shafts from a brass rod & 4mm thread for prop I just hope it don't leak to much I'll use grease in the stuffing box that's a brass tube that prop shaft goes through .There was a lot of cutting needed so propeller has clearance. All these parts will need to be epoxied in place. Then stern area can be re-shaped .
▲
⟩⟩
hermank
Peejay
Len1
RNinMunich
EdW
Fred
RodC
📝 Yard Sale Find
7 months ago by 🇨🇦 GARTH ( Captain)
Captain)✧ 113 Views · 12 Likes · 1 Comment
Flag
💬 Add Comment
It was a great day to sit out side & do a little cutting & gluing So I decided that my Galion will need a rounded stern if it's going to be a tug boat .Because Ernest Shackleton ship the Quest was found by the Royal Canadian Geographical Society and the wreck was 1,280 feet below the surface of the northwest Atlantic Ocean roughly 15 nautical miles off the coast of Labrador. It’s sitting on its keel, with its broken mast lying on the seafloor nearby. I thought that that could also be made into a R/C ship .Can't make up my mind .
▲
⟩⟩
Commodore-H
RNinMunich
Len1
ChrisG
hermank
Wolle
MartinW
EdW
Peejay
LeeA
RodC
IanL1
|
💬 Re: Yard Sale Find
7 months ago by 🇬🇧 roycv (
 Vice Admiral)✧ 102 Views · 3 Likes
Flag
Hi Garth when I go to look at your pictures they get smaller rather than larger!
Roy ▲
⟩⟩
Peejay
Len1
hermank
|
Login To
Remove Ads
Remove Ads
