Managed to capture some video of Brian Clewes' live steam TID tug on the lake this Wednesday 19 October. First chance for a proper sail and a bit more ballast needed.

This was my very first RC project. In fact, it was only to be a static model, but then things changed.
Currently she's a shelf-queen as the rigging takes a while.
She can be converted to a fishing boat and fitted with a 5 blade 42mm prop and brushed 540 motor.
The sail rudder is larger and requires the prop to be removed.

Had a little trouble getting my sound to work properly but with a little fiddling got it working a lot better had to reverse motor leads & switch transmitter forward -reverse switch so it would work in forward direction .

On Halloween morning Sunday Oct. 31 2021 ran the Sequin with several other club members at Spencer's pool may be last run this year with weather getting cooler . The lake freighter was her first run & just needed a little ballast weight at the stern prop wasn't deep enough Boat belongs to a fellow club member .

Sun was out, wind was down, so took the boat for swimming lessons. Went very well, no problems other than the silicone couplings trying to screw themselves off as usual, (too much bite and torque) and bunching up to the motor causing friction), (have a possible fix I'm working on for that today) Heaps of power from the 2 - 540 HV brushed motors only running on 3s. Never went much more than a tad past 1/2 throttle which was spot on scale wise.

Very quiet as well, - mind you, couldn't hear much anyhow with a road milling machine working at the end of the pond about 150m away, at around 80db where I was!!😠😠😠😭 Of course it would have to be there today,! something like this always stuffs my plans up, cars, trucks, screeching seagulls, people talking to you while you are trying to make a nice quiet video etc etc. Can't seem to get away from noise. Added to that, the video's crap,- as soon as it uploads to YT it turns to rubbish,- was quite acceptable till then.

Must be the wide format they use, as it's fine in a small screen (ie YT preview) and my computer. Worst thing is, it took an hour to load this rubbish on a fibre connection!! Not loading any more till I get a better camera, "Santa, did you hear that ?"😁

I might de-power it a bit, as it has too much power really,- might put 2 540 45T motors in which will run on 2s nicely with 30mm props (has 35s at the moment) and not be as touchy on the throttle. You can steer this just using the throttles it's so bitey. Spins on the spot like a jet boat as well. Stereo worked well, but the IR remote doesn't like working too far away in bright sunlight, (have a separate vid, but YT would give a copyright warning, so I won't put that up) The vid is garbage, but you'll get the idea😁

Finally had a chance to do a test on Pilot 40 project that was my lockdown stay home project . Change the props to 50 mill.4mill.threaded & now I have right prop & left prop Replaced the Sabertooth speed control as it was to hard to control with my Airtronics transmitter used a standard Hobby King speed control changed the wiring terminal block to a larger size as the one I first used was to hard to put wires in it . I always have trouble with mounting so glued the motors in with some goop & there just fine now

Fitted the new 550 45T brushed motor as a replacement for the ancient and slow 70s Graupner monoperm. Goes a lot better now and has a decent speed range. Handles and rides quite well for a skinny boat. Prop is a Graupner 40mm 2 blade (don't know the pitch, -fairly fine) Using a 2200mAh 2S LiPo battery which probably gives around an hours running slowly, or 30 mins of hooning around.

Battery was only charged to 8.25v and ended up at 7.7v. (45%) after about 3/4 hr. I'll probably fit a Hobbywing ESC as well, for a bit better reverse action, as the El cheapo car one is a bit slow finding reverse at times.

Typical yorkshire weather, after 5 minutes it chucked it down so had to make a quick retreat. used just one 2200 3s lipo for now but need a bigger lake/pond really as can only give full power for 3-4 seconds, so stop -go is not good but was hoping to get some good photos-videos, but the rain stopped play till another day.
Edit, forgot to mention. most of run on centre prop only. the last 5 seconds or so is full power, well nearly.

I've replaced the old 6v sealed wet battery with a lipo 3s,11.1 volt 2200mhz, 100c spectrum smart battery. so the 1st run was cautious i just fired up the centre prop to see how she performed, well i was surprised at the turn of speed she had on just 1 prop, and how well she planed, it was a little awkward filming and controlling the boat by myself as i was the only one pond side. this was not without mishaps though, see 2nd video
After checking the boat over she was found to be unmarked and no bits missing, not bad to say she hit the pontoon at full speed, took off and plunged back in at the other side.
So the second run i started on the centre prop and then opened her up on the outer 2, she shot forward and immediately stalled, dead in the water. luckily i could reach her with the ponds barge pole to pull her to the side. i found the fuse had blown , i had fitted a 20amp mini flat fuse, i didn't have a 30amp only another 20amp which blew just as quick, upon opening up the outer props.
any ideas anyone or will a 30amp do the job, or a 2s battery? help any suggestions considered.
Roger

Part 1. ideal conditions; nearly 30°C, cool Bier at hand😜
Sea Scout built by Dad in the early sixties with a Taycol Target and 6V lead acid wet cells (very wet😡). Renovated and dragged into the 21st century over the last several months 😉
See Build Blog 'Sea Scout 'Jessica'' for details!
Motor: Propdrive 2830, 1000kV, 30mm 3 blade Raboesch prop. Quicrun 16BL30 (30A) ESC with BEC.
Tested with 3 battery types, all started with 99% measured capacity-
1. NiMh 4.2Ah 7.2V, nom. 408gm.
Result: Speed sedate (OK 😉scale river cruising!) No planing.
Max current: 3.6A
End status V / capacity left: At end of short run ca 3 mins. 7.78V 99%.
2. 2S LiPo 4.0Ah 7.4V nom. 257gm.
Result: Speed still sedate but due to lower batt weight at least the forefoot came out of the wet stuff! Max current: 4.1A
End status V / capacity left: At end of short run ca 3 mins. 8.25V 93%.
3. 3S LiPo 4.0Ah 11.1V nom. 315gm.
Result: Now we're getting somewhere!!😁
Good speed, manoeuvrability and planing 😊 Max current: 7.5A
End status: 11.95V 74% after several long runs, ca 20 mins total.
Estimated (extrapolated) endurance on a 4Ah LiPo around one hour - mostly 'full bore' - 'Pedal to the metal man' 😊

See also:

The competition!

Final run. (Beer was getting warm😁)

Cap'ns log entry:
Boat dead-weight w/o battery: 1.8kg.
Spray rails to be added!😲
Slight list to port to be trimmed.
Rudder servo to be reversed!!😲
Keel protection to be added: some scratches and flaking from stony sloping shore 🤔
Summary: much as expected👍 Forget anything less than 3S.
Anyone want to buy a batch (4) of new 2S 4Ah 45C Lipos? 'One careful owner'!
Happy boating people, Cheers Doug 😎
PS Many thanks to Camera girl Gisela 👍
Recorded in 1080p HD.

well finally got there. she sits a little low in the water, but evenly along the water line. this was with the battery central to the hull. when powered up the centre screw alone moved her quite serenely and was very manoeuvrable. when power was added to the outer screws I would say she didn't plane well as she wasn't going fast enough. even with all props on full power, I think also she is to heavy and the battery too far forward.
So to remedy this I moved the battery back a compartment, positioning it over the 3 motors , it was a tight squeeze, but fitted just.
This sat the stern down a little and the bow up and gave the impression of planeing, she still not fast enough though. the scale speed still doesn't look right.
I'm going to have to have a rethink on this one. having said all this though she looked well in the water if i say so my self.
Roger

Set the new Surpass 3000KV 36 diam finned in-runner up in the boat, and did a tank test. Lots more power than the HV brushed 1200kv 550, but with higher idle. Re-did the reinforced silicone coupling and fitted a small collar to the inner end of the motor shaft to hold the tube from moving forward against the motor, as with the extra torque of the in-runner, it was trying to twist the tube off the shafts. Seems to be hanging in there static which is a promising sign. Once running, the load will come off which should help.

Runs full at around 4A and the battery holds at around 3.8v/ cell )alarm is set at 3.6 for safety, (as a sort of rev limiter) performance should improve a bit now. Have to wait till tomorrow as the restrictions end at 6am Sunday, (then have to hope for good weather for the test) The prop in the jet is a 28mm 3 blade racing prop which I modified to fit. Don't think I'm going to get much more out of the jet unit without it exploding😁, (it's only plastic I think, not GRP), - might have to buy a back-up and fit it with better quality bearings etc. If the jet was in the usual 'plastic' 24" toys it would be a rocket, but it's pushing 6lbs which is a challenge😀

Note the police chase outside in the background😁- always action around here, lots of hoons in cars😁