๐ wren rescue boat
9 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
Has any one got photos of a wren rescue boat age about 1950-1960 as I have been given one as a progect
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Decals
10 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
HI Model Flags do them for a 46in fireboat I dont know if they do them for a 34in you could have look on line or give them a ring
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ฌ Aerokits 46" Fireboat twin screw brushless conversion
10 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
HI just looked at your phots seems to be a too large gap between pros and rudders and I would try larger rudders
mihael1
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ฌ Aerokits 46" Fireboat twin screw brushless conversion
10 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
HI I have just finished my 46 in fire boat with twin brushless motors my props rotate inwards and turns all right at low speed I did fit very large rudders with 50mm 3 blade props
michael1
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Help on paint and varnish for model boat
10 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
HI I would never recommend any one to put spray cans in hot water or use a hair dryer just leave the cans at room temperature for 24 hours before using the main temperature is the air temperature should be a min of 55F if cooler spray out doors and bring in as soon as you can to a room tep of 60 plus I was a sprayer for 25 years
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Windows
10 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
HI they go in between the frame thats the way I put them on my 46in fireboat and the frames go on the side try to get the windows flush with out side.
mike
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ฌ RAF Crash Tender 46in
10 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
I have to disagree when you say that brushless motors are power hungry I have one more boat on a brushless and get a longer run than with brush motors a lot of members in our club use brushless with good results
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ฌ RAF Crash Tender 46in
10 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
HI Dave M The motors are 2 KED THUMRUN 2837/18 Outrunners with 2 45mm three bladed brass props 9.6 volt battery waiting for 50mm props to come as members in my club think I will get a bit more speed
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ RAF Crash Tender 46in
10 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ 34" GRP/Kitshak Crash tender
10 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
HI Zippy you need to go to a web site called Giant Shark that is were I get my brushless motors from you will need special speed controllers for brushless motors hope this helps
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ aero fire boat 46in
11 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
Thanks I will try to make mine
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ aero fire boat 46in
11 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
HI can any one tell me were I can buy the roof rails for a 46in aero fire boat I have got all the rest of the fittings
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received
๐ Gloucester & District Model Boat Club
11 years ago by
๐ฌ๐ง michael1 (
Able Seaman)
Flag
▲
โฉโฉ
No likes yet
This member will receive 1 point
for every like received