Search
838 posts for “hull paint” · in Blogs
Page 29 of 30
Blog
Wallasey III Mersey Ferry
… ut for saloons and access to interior. 2 Starting the spray paint work to the hull. 3 Cut always for bollards and gangway access on the raw hull 4 Main deck supports on hull interior a 1/4" soft wood strip glued with epoxy to the hull at co …
Blog
A Cullermix tug conversion
… he first things to do were to strip it all down to the bare hull which meant removing the entire bulwarks and deck as well so that literally all I had was the wooden hull, this was then stripped of all paintwork and the inside varnish. The …
Blog
Graupner Collie - part 2
… nning plus epoxy and then the fairing process repeated. The hull was then stripped back, smoothed and primed. Next a new keel ballast weight was shaped in wood, then used as a plug to make and mould and cast (in lead) a copy with embedded p …
Blog
AEROKITS 46" FIREBOAT....A TROUBLED PROJECT
With all the original paint removed, the flaws in the hull are to be seen, were the patches of paint have not come off, after the hull had been sanded. The next stage was to attack the engine room, as mentioned this was originally IC powere …
Blog
Paddler Project
… onged wet spell has finally got me doing something with the hull & wheels I now have. Please allow that I have no machine tools and only a little cluttered shed, and probably minimal skills. But I publish this in the hope that it might enco …
Blog
AEROKITS 46" FIREBOAT.....A TROUBLED PROJECT
Well the first job was to remove the original paint work, normally this would have been done with the good old paint remover "Nitromors" which works well but can be very messy....but after an e-mail from a fellow club member he recommended …
Blog
Assurance Class Tug
… eck of the Assurance Class Tug now ready to be put into the hull, the towing hook box area has been made stronger to insure that it can pull without breaking. Now to get it ready for it undercoat of paint.
Blog
Inshore fishing boat
The main planking of the hull now finished. I had intended at the start of the build to paint the hull but because the planking had gone so well and no filler was used, I would sand, stain and seal it. A coat of Z-Poxy was applied to the in …
Blog
Aerokits 46" Fireboat twin screw brushless conversion
That textured paint was from B & Q, it gives rough finish, and is just right. I masked off a thin strip around the hull, and any fitttings that where on, and painted with BS631 that I had mixed in an aerosol at a car paint suppliers Finally …
Blog
Aerokits 46" Fireboat twin screw brushless conversion
… spect for anything unusal that should not be happening, and paint, boring! My paint process for the hull, reclean, sand with a block using 800grit, its already primered, paint the red, 2 or 3 coats, flat with 600 then 800 wet/dry, clean off …
Blog
Aerokits 46" Fireboat twin screw brushless conversion
so a brief recap hull is primed and ready for paint, after being treated with glass cloth and resin. Work has been completed on cabin sides, prop tubes are fitted, and the method for fitting the motors done (anybody looked at the video in t …
Blog
Aerokits 46" Fireboat twin screw brushless conversion
… you can probably tell, I'm racing through the glassing, and paint prep. its a real Important part of the build, but I found it soooo boring! Not long before the real interesting stuff comes along, especially the driveline Time to turn the b …
Blog
Aerokits 46" Fireboat twin screw brushless conversion -
paint, at last, I have opted for halfords filler primer, dont know why, I was disappointed last time I used it , but will give it another go. The hull is quite nice and flat, after a LOT of rubbing down, I wanted a primer that will allow so …
Blog
Aerokits 46" Fireboat twin screw brushless conversion
… mentioned previously, we decided that we need to glass the hull, this will make sure the wood does not rot in the future, as we dont know how old the boat actually is. The hull was a bit of a job, getting the cloth and resin around the sha …
Blog
Aerokits 46" Fireboat twin screw brushless conversion
Next bit is horrible, preparing for the paint. With my smaller 36" Fireboat, it suffered after time with delamination, so I decided to fibreglass this boat, I had only done this once before, so was dreading this job. The photo is the fibreg …
Blog
Glenn Aerokit 36" Mk2
Painting went quite well, the only snag was the red which kept bleeding through the black. The white line was I think successful, although a bit of a fiddle to get flat over the chine line, doing It on a hot day helped. The grey primer uppe …
Blog
Sea Trials
… t is generally complete - still haven't really finished the hull painting although I did run it on Goole MBCs pond a few weeks back. it goes like stink with the Hobbyking 1000kv Brushless Motor and 7.2v NiMh battery pack and shows very long …
Blog
Rethink on Ballast
The lead inside the hull made the model very heavy and difficult to handle. Other club members have been using detachable fiberglass keels on their yachts so got Brian to make me one. Had a right struggle removing the lead and needed to rep …
Blog
"Rainbow" 1934 J-Boat Class Racer
… Everything Is a build-up, Including the mast and boom. The hull: mainframes were assembled on the keel, and attached to a strongback for planking. Bow, stern, and keel blocks were Installed. The whole thing Is sanded to shape, sins filled, …
Blog
Decking Completed
… ace and rubbed down ready for varnishing. So hope to finish hull prep in the next few days, then on to the painting and varnishing. I will also be fitting the cabin roof's before commencing with the painting, as I like everything prepared b …
Blog
Resin and Glass Cloth
… me use kitchen. The pictures show my next step, I've coated hull in sanding sealer followed by sanding to a reasonable finish. Then coated with Eze-Kote resin from Delux Materials, then sanded back lightly. I then covered with 24gsm glass c …
Blog
Motor Sailer
… d was the curve of the wood especially on the bottom of the hull, I now have a gap to fill In. Then came the deck and the housing etc all drawn out first then cut and glued. The keel Is my own Idea as I want to fit a propeller still. Finish …
Blog
A 16ft tanker towboat
… and 2ft wide with sides 10" deep. she has no bottom in the hull sections which are 2ft x 2ft, instead she has 4" of foam fitted up under the deck which she floats on, this leaves the sides acting as a long keel and stops her slipping about …
Blog
Cariad Scratch build
… ng for help with building his recently acquired Cariad. The hull is available from Chris Brown (Google for details) complete with plan and he also offers a fittings kit and sails. I have decided to start this new blog to share the process f …
Blog
Glenn Aerokit 36" Mk2
… an overworked kettle apparently. it never got a top coat of paint or radio, the latter as it was too expensive at the time for him. There it rested until the early 80's when a 14 year old me painted it the wrong colours (but not far out), p …
Blog
a yacht yet to get a name
… that looked like a good start came up, a timber built yacht hull, not too far away for collection only. When I bid I did not really know what is was, as it was made as a static display, but as it sold at the starting bid price 99 p. I was n …
Blog
PT301 (Snuffy Smith)
… 00 brushed electric with 2.4 ghz R/C. The clear coat to the hull has shrunk and cracked so a new rub down and re-paint needed. Hopefully all finished for Fleetwood Vintage day in June.
Blog
Reached the tedious bit of the build. . .
… er of tissue on with the second coat of sanding sealer. The paint has been bought for the main part of the hull - dark metallic blue. There will be a couple of coats of white high-build primer before the final colour coats. ~~~~~~~~~~~~~~~~ …