Join Us On Social Media!
|
|
|
Download The App!
Login To
Remove Ads
Remove Ads
Login To
Remove Ads
Remove Ads
Model Boats Website
Commander)
Liked 8 Channel Transmitter 4 days ago
Liked Re: Krick Paula | Work / Crane Boat 8 days ago
Liked Re: Krick Paula | Work / Crane Boat 9 days ago
Liked 8 Channel Transmitter 9 days ago
Liked 8 Channel Transmitter 9 days ago
Liked 8 Channel Transmitter 9 days ago
United Kingdom
Recent Posts
📝 Rudder & Propshaft Drilling
8 days ago by 🇬🇧 Heners2332 (
Master Seaman)
Master Seaman)✧ 28 Views · 4 Likes
Flag
💬 Add Comment
Today we have drilled out the holes for both Propshaft and rudder, 6 and 4mm respectively. It is best to drill around 0.5mm more than specified in my opinion, as filing of that amount is otherwise necessary.
Attached are photos of drilling and the finished product with rudder and shaft loosely installed.
I also recommend drilling a small pilot hole, of 2 or 3 mm to ensure the larger drill bit drills straight and accurately.
The next stage is cutting out the deck ( the hatched areas which I have circled in the image). These will be the superstructure and servo access points.
Attached are photos of drilling and the finished product with rudder and shaft loosely installed.
I also recommend drilling a small pilot hole, of 2 or 3 mm to ensure the larger drill bit drills straight and accurately.
The next stage is cutting out the deck ( the hatched areas which I have circled in the image). These will be the superstructure and servo access points.
▲
⟩⟩
thadlietz
Rookysailor
Chum444
jumpugly
Login To
Remove Ads
Remove Ads
💬 Re: Krick Paula | Work / Crane Boat
9 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 36 Views · 1 Like
Flag
💬 Add Comment
Jumpugly, yes! That’s what I must do, if I could find any rubber strips 😂
▲
⟩⟩
jumpugly
💬 Re: Krick Paula | Work / Crane Boat
9 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 45 Views · 1 Like
Flag
💬 Add Comment
RodC, unsure but the battery is around 600g as it is a 6v Lead Acid as per Kricks recommendation.
▲
⟩⟩
thadlietz
📝 8 Channel Transmitter
9 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 58 Views · 2 Likes
Flag
📝 Reply
Wolle , up to around £150 as I will now just use this transmitter for all models.
▲
⟩⟩
Wolle
hermank
📝 8 Channel Transmitter
9 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 65 Views · 2 Likes
Flag
📝 Reply
Does anyone know if there is an 8+ channel transmitter with a spring centered throttle stick (right hand stick) ?
▲
⟩⟩
Wolle
hermank
📝 8 Channel Transmitter
9 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 68 Views · 2 Likes
Flag
📝 Reply
MartinS, Is there a flysky that can have spring centered throttle stick? Was looking at the FT ST 8 & 16 but they are not springed so sadly not an option. Radio link may be an option.
▲
⟩⟩
Wolle
hermank
💬 Re: Krick Paula | Work / Crane Boat
9 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 57 Views · 5 Likes
Flag
💬 Add Comment
Today we started the project by constructing the stand, it is made out of Laser cut plywood and is therefore a very precise cut. Once the parts were removed we sanded down and glued together. It forms a well constructed and sturdy stand for the boat.
Not an exciting start, but Step 0 is always required!
Not an exciting start, but Step 0 is always required!
▲
⟩⟩
thadlietz
DuncanP
PhilH
hermank
RodC
📝 Krick Paula | Work / Crane Boat
9 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 57 Views · 3 Likes · 5 Comments
Flag
💬 Add Comment
Kit Build bought from Krick. Formerly a Robbe Kit but now known as Romarin by Krick.
72cm length with a 600 motor ( eventually!)
72cm length with a 600 motor ( eventually!)
▲
⟩⟩
thadlietz
hermank
RodC
📝 8 Channel Transmitter
9 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 65 Views · 2 Likes
Flag
📝 Reply
If I were to go fly sky, what would be recommended? Which specific controller?
Thanks
Thanks
▲
⟩⟩
Wolle
hermank
📝 8 Channel Transmitter
10 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 63 Views · 3 Likes
Flag
📝 Reply
Hi, I need to get an 8 channel transmitter for a Krick Paula, it will
Need to be able to operate the crane (up and down), winch ( out and in) and some lights. Was looking at the Microzone 8B, don’t know if it’s any good however?
In short I’m looking for any recommendations or advice on to which transmitter may be best and if the microzone could do what I need it to do.
Need to be able to operate the crane (up and down), winch ( out and in) and some lights. Was looking at the Microzone 8B, don’t know if it’s any good however?
In short I’m looking for any recommendations or advice on to which transmitter may be best and if the microzone could do what I need it to do.
▲
⟩⟩
Wolle
hermank
RodC
💬 Re: Fire Crash Tender
17 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 43 Views · 1 Like
Flag
💬 Add Comment
Thanks very much, it might be a project that is putting to the side for now as I have a Kit for a Krick Paula to do for the New Year and shortly. I will be documenting this as I build it and then after that’s done I may alter the Crash Tender, it depends whether I should or not, I don’t know whether to keep as is ( because I know it doesn’t leak and works ) or change some stuff and have the risk of further leaks.
▲
⟩⟩
thadlietz
Login To
Remove Ads
Remove Ads
💬 Re: Fire Crash Tender
17 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 44 Views · 2 Likes
Flag
💬 Add Comment
Hi Robbob,
The leak has now been solved and it was identified to have been coming in through a very small crack that opened as the boat vibrates, this has now been sealed and the leak has been fixed.
Sadly the prop shaft cannot be removed without tearing out most of the hull where the shaft is, this is because when we purchased the boat the builder had installed the shaft in a way that is is impossible to remove without having to replace 1/4 of the hull.
We purchased the boat as a project that needed a lot of work so it’s not too perfect, just working order. Adjusting the angle of the motor and couplings is also not possible as to remove the motor block the internal wall it’s next to would need to be removed
, this is epoxied onto the hull walls and would cause damaged if removed.
So all in all there is not much that can be done but what is currently there.
The red unit is, as far as we can work out, a gearbox or a unit to adjust the length of the shaft by a few mm. It has a servo mount on it so our thinking is you could control a servo that would change the gearbox to differ the speed. This is what myself and the boat club I go to presumes.
Thanks.
The leak has now been solved and it was identified to have been coming in through a very small crack that opened as the boat vibrates, this has now been sealed and the leak has been fixed.
Sadly the prop shaft cannot be removed without tearing out most of the hull where the shaft is, this is because when we purchased the boat the builder had installed the shaft in a way that is is impossible to remove without having to replace 1/4 of the hull.
We purchased the boat as a project that needed a lot of work so it’s not too perfect, just working order. Adjusting the angle of the motor and couplings is also not possible as to remove the motor block the internal wall it’s next to would need to be removed
, this is epoxied onto the hull walls and would cause damaged if removed.
So all in all there is not much that can be done but what is currently there.
The red unit is, as far as we can work out, a gearbox or a unit to adjust the length of the shaft by a few mm. It has a servo mount on it so our thinking is you could control a servo that would change the gearbox to differ the speed. This is what myself and the boat club I go to presumes.
Thanks.
▲
⟩⟩
thadlietz
robbob
💬 Re: Fire Crash Tender
19 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 54 Views · 4 Likes
Flag
💬 Add Comment
The prop size is M4, we had a leak but that is now mended. I shall attach an image of the underside.
▲
⟩⟩
thadlietz
EdW
BOATSHED
hermank
💬 Re: Fire Crash Tender
19 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 62 Views · 3 Likes
Flag
💬 Add Comment
Battery is currently located in the forward cabin where we have made a slot for it to sit nice and snug inside.
▲
⟩⟩
thadlietz
hermank
EdW
💬 Re: Fire Crash Tender
19 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 65 Views · 4 Likes
Flag
💬 Add Comment
Yes I shall attach one, we are still fiddling with weight distribution and need to get more lead for the rear. Should plane nicely once done.
The other possible battery location is the receiver compartment as pictured, we would have to install a battery stand.
Ignore the sponge!
The other possible battery location is the receiver compartment as pictured, we would have to install a battery stand.
Ignore the sponge!
▲
⟩⟩
thadlietz
hermank
EdW
BOATSHED
📝 Guestbook
20 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 56 Views · 7 Likes · 1 Comment
Flag
💬 Add Comment
I love that modellers,
Experienced or not, can talk, ask questions and document their experiences and struggles.
I shall definitely be documenting my new build arriving soon, a Krick Paula.
Experienced or not, can talk, ask questions and document their experiences and struggles.
I shall definitely be documenting my new build arriving soon, a Krick Paula.
▲
⟩⟩
IanL1
jumpugly
hermank
Steves-s
GaryLC
Mike Stoney
RNinMunich
💬 Re: Fairmount Alpine
20 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 31 Views · 1 Like
Flag
💬 Add Comment
No Worries 😀 Check out the other boat in my harbour, my aerokits 46’’ fire crash tender. I have put a video of it on.
▲
⟩⟩
hermank
💬 Re: Fire Crash Tender
20 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 86 Views · 2 Likes
Flag
💬 Add Comment
She was running at around 3/4 throttle. The battery I have in her is a 12v Lead Acid, gives plenty of run time and is easy to use and charge.
▲
⟩⟩
hermank
BOATSHED
📝 Fire Crash Tender
21 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 17 Views · 9 Likes · 17 Comments
Flag
💬 Add Comment
Original Aerokits 46’’
850 motor
850 motor
▲
⟩⟩
Mike Stoney
thadlietz
JOHN
EdW
Ray
PeteJev
BOATSHED
jumpugly
hermank
📝 Fairmount Alpine
21 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 17 Views · 5 Likes · 2 Comments
Flag
💬 Add Comment
Purchased Built
▲
⟩⟩
BOATSHED
DWBrinkman
LeeA
xtramaths
hermank
💬 Re: She’s done!!
21 days ago by 🇬🇧 Heners2332 ( Master Seaman)
Master Seaman)✧ 31 Views · 1 Like
Flag
💬 Add Comment
Hi, 4 years later I’ve got a question.
What battery did she have? Thinking of building one and need to know what is best to buy.
Thanks
What battery did she have? Thinking of building one and need to know what is best to buy.
Thanks
▲
⟩⟩
hermank
Login To
Remove Ads
Remove Ads
