Getting more experience with new camera boat seeing how the gopro handles the varying light changes. Filming at different locations, while circumnavigating the lake.
Live streaming via the phone, changes to exposure etc. were applied in the final edit.
Again , thanks to Bill & Ben - and of course Graham !.

Camera Boat 5 uses another simple "pontoon" design with 90

rotating motor and fan unit with rudder which was added later. Gopro was mounted on rotating servo which gives 360

vision.
Camera operated with phone using Gopro App.
Regarding filming techniques etc. - Still plenty of issues to improve and overcome along the learning curve !.

Mni Tnx Graham for being there with "Bill & Ben" and Jon G7NFK for all your previous help and support since my stroke.
#rccameraboats
#rcsailing #rcboats #bmbc

The other part of the video (from the new camera) Finally found an editing program for it (cost me $40 though!) - I need one for MOV, as for some stupid reason, the makers of the camera use Apple Quicktime MOV which is a pain. Should be set now for editing.

New coupling with the cable ties seemed to hold up well this time, although the throttle end point is set to 80%,- looks scale enough as it is though.(only a 2400mah 3s battery, so not a long run time if you are going flat out- can suck 35-40A!). Pity the launching vid was rubbish, but have the amphitruck sorted with a towbar now, so I'll give it another crack when there is a good day.

Second go at getting a decent launch vid, - tricky when backing in as you have to manage steering, fwd/rev and handbrake together, (plus having to use 2 TXs and 2 cameras. ). Getting slightly better at it. Next time will be launched by the amphitruck, as it's bigger, heavier and has better grip, (and 4x4 rear drive.) Ramp was a bit wet and slippery for the jeep, (would pull it up in the dry ok) I have a 4k vid of the boat from the new camera, but need a new editor for MOV vids.

Decided to drag the seaplane tender out, as I haven't run it for quite a while, and to test the new camera which is mounted on the TX back handle, rather than on my head. A lot quicker and easier to mount, and you can see what you are shooting. I have modified a backpack camera clamp, so it fits 3 different TXs in seconds.

Probably be making some better couplings for the ST, as the silicone tubes are starting to work up to the motor bearings and rub on the front housings.

Just a simple model I built for my son about 14yrs ago. He wasn't interested (more into computers) so I use it for the salt water. Just a brass shaft and 12v high speed 380 motor, runs quite well. Ran it to try out the new 4K camera, (set on 1920x1080) but had to convert the vid from MOV to MP4 to edit it, so it reduced the clarity a bit. At least it doesn't have a blurry bit in the middle of the lens like my 10yr old one. have to figure out a better way, (or get a better editor)

This might be clearer

Just a quick update with the new camera boat before fitting and running with the Gopro attached.
Observations :-
1. Maneuverability - Great - but better control with high and low rate options!.
2. Speed - Too much ? - may be , but enough for me to throttle back quickly !.
3. Camera - Good balance and rotation for 360*.
4. Cost - Minimal - ie. Motor & ESC kit from Hobbybitz.
5. Noise - 5/10
6. Fun Factor - 10/10 - just for fun ! - enjoy RC Sailing !.

NOTE - I would be interested to know of any theories in respect of the "PULSING NOISE" of the motor ?????
Cheers
Phil

The Odessa is fitted with a action camera to record her journeys. This video was produced as a trial. The Odessa has recently been resprayed in metallic red and the little dingy was removed.
She now also has a crew of three.
1:20 scale - Lindberg kit built.

Filmed mainly from my camera boat, this video illustrates a new model boat constructed by B.M.B.C member Dean Ratcliffe - see full information below for Build & Background info from Dean

Forgot my helmet for the camera, so only got this short land vid.

From a design concept incorporating an old power boat destined for the rubbish tip ! - to a functional Camera platform to capture some of the fantastic models that sail at our local venues.

The emerging creation ( all be it rough and ready !) will incorporate rotating fan motor and 360 degree rotating camera with live feed FPV camera.

My enjoyment is to capture the the skill, time and effort that fellow modelers put into their creations - whether they be they scratch built, own designs, kit sets or off the shelf.

As Requested :- Link to previous Camera Boat (SwampDawg)
** **

Time for a new camera boat to emerge - Will it meet my 5 criteria ? !

Just for fun !

Phil👍⛵