More work on the little boat today #lockdownfun

Finally got a good day, so raced down to the pond and threw the boat in. 2 problems, 1: battery had run down a bit with all the testing, and the new 18kg digital servo winch needed every bit of 4.8v, so functioned intermittently, meaning not much sail control, 2: jib boom needs a kicking strap to stop it 'skying' and tangling (knew it would happen but wasn't a worry). Apart from that, everything worked perfectly ( cheapo China Futaba knock -off rudder servo still worked fine on the low battery which is a bonus)

Sailed brilliantly like it did over 40 yrs ago, and as it's set will sail hands off on a reach, being nicely balanced, (even with the crappy jib,- which I had to make,- well actually my mother made for me,- back in 1980 after the original was stolen by a kid at the beach, while my back was turned😠) Funnily enough it was made on the same Bernina I used to sew (horrendously) the jib foot after trimming it for the boom a few days ago.

A few more things to improve and add, but pleased to have it back on the water. Another crap video, -seems to get blurry once it's been through the movie editor and You tube ) One day santa might bring me a Gopro, ("yeah right"!)

Second test was slightly better, using the aluminium spiral cut universal which came with the jet unit. As you can probably hear, it was horribly out of balance (even with cable ties to reduce it). It was not even drilled centrally and the spiral is right hand when it should be left hand, (like a spring twisted against the wind, it wants to deform). Slight improvement in speed on the first test (no slip this time) but the noise was horrendous.

Have pulled the jet apart and found that the 3 blade prop is around 1 mm too small for the hole, causing cavitation (see loads of bubbles in the jet stream) which is causing loss of thrust. The prop is the wrong type as well, with rounded blades, so I have modified a larger prop with more pitch to fit snugly in the unit to hopefully increase thrust. The shaft is also wrong, with a flat cut almost half the diam and carrying on through the bearing, allowing the grease to fly out.

I actually saw a Chinese site on Al Expr stating that "some dimensions on the product may be different due to the number of machines and operators involved in its' manufacture," SERIOUSLY!!??? their quality control must be utter crap and the operators not skilled enough to eat their lunch😐 Why bother having a dimension at all?? Little wonder nothing fits properly.

Unfortunately, most model shops sell the very same stuff, unless you want to shell out muchos dolleros for European stuff. I have just ordered some 4mm silver steel to make a new shaft, so a coupling or silicone tube will fit better. Also ordered some solid connectors to try. Vibration is wasted energy so it needs to be eliminated. Hopefully the mods will improve things and allow the motor to run on 4s rater than 3s. Worked out that the motor is only 1200KV, so it's only doing around 13,000 rpm under load. Probably will need around
18,000 rpm for proper performance. Onwards and upwards (or forwards as the case may be.😁)

Sorry about the blurry vid again, but my camera lens is knackered.

Smoke air and water switching sequence, (sound's out of sync for some reason,)

A bit more refinement on the timing but getting there. Finally got the voltage regs from China to complete the system. A bit noisy, as the water pump is dry,- quietens down with water. Switches in stages using Grahams magic timer, - 1. smoke on, 2. water and air on. There is actually smoke running constantly at a reduced level once everything is running, but very hard to film. I could turn it up but I don't want it to look like it's on fire😂

"Fairey Huntsman" - Following renewed recent interest from Model Boats Website members,
here are three variations from BMBC members of the popular "Huntsman".

(Ref from Wikipedia)
Fairey Huntsman / Fairey Huntsman 28 / Fairey Huntsman 31: The design of the Huntsman and its smaller sister, the Huntress were the inspiration of Ray Hunt and designed by Alan Burnard.

A couple of shots taken at Dovercourt in September 2016. I was visiting and so am not able to tell you anything of the boats or skippers. Dovercourt is a salt water pond and plays havoc with switches and brass fittings.
Geof L.

Test no 2 with deflector plate above jet unit,- stops water running up the transom in reverse. Changed cameras so vid is slightly better than the last rubbish😁 Also demonstrates the jets ability to have fwd, neut and reverse while running in one direction.

This will be last Sequin Tug run for 2020 weather great for Nov.6th it was 19 C today & will be nice weather for the next few days Then the cool weather will be back again . You can see that most of the real boats are now out of the water & are now in storage for the winter because Hamilton Harbor usually freezes over .

Had a large moment of enthusiasm yesterday and fitted the jet unit and associated bits. Then it was time to wet its bum for a test. First off, the jet wouldn't suck water without pushing the stern down slightly, (as I expected due to the boats' light weight.) I added 300g to the stern and she was away😊 Happiness filled I were😁!. Reversing bucket works very well (even though it's a bit of a blob on the transom). You really need one if you don't want to go forward forever, trying not to 'sail yourself into a corner'.

I Need to waterproof the pushrod holes in the transom but the bellows I bought are too stiff and compress too much, so I'll have to come up with another method, (probably some deflectors for a start. Only a problem when in reverse with a bit of throttle on. Plenty of power with the 2s I was using, but motor is rated 12-24v so it would scream, -even with a 3s. I'll start with 2s and see how it goes. Might have an initial blast on the lake this week if all goes well, although I'd like to finish the deck bits first.

Just waiting for some Voltage regs to come so I can complete the electrical side with the fancy bits.. The mechanical and electrical sides are as good as done, Grahams timer is working perfectly, with the water pump and air pumps hooked up (going to install a VReg on each one plus the smoker).

Shades of Autumn - Thursday sailing with Buxton Model Boat Club at the Pavilion Gardens Lake Buxton Derbyshire SK17 9AY.

Managed to connect up the motor once all the drive bearings were in.. first video is with a 7.2v battery (which was actually nearly flat!) and then in the second video with a fully charged 11.1v lipo!
Might get the Atlantic RIB to plane yet..