Completed (nearly, still a few more crates needed) in July after a 2 year build on a Kingston Moldings hull. Not a scrap of plywood has been used, all made from Oak, Mahogany, Beech and brass. All fittings scratch built, boiler from Maccsteam in Macclesfield, engine TVR 1 A BB from Macclesfield model engineering supplies. Runs on 60/40 butane propane mix. Radio 3 channels used on Futaba 6EX 2.4 ghz set, 1 fo1 for fwd/reverse, I for steering.

This was in a sorry state when I acquired it but here it is after restoration and 2.4Ghz radio fitted.

Named after my wife Sheila, the yacht was purchased from the builder, as I don't do yachts, but thought I had better have one for those windy days when scale models become tricky. She behaves well, (as does the wife). Only Radio control on the rudder; the sails are set depending on the wind strength.

Maiden voyage.
One or two little issues. Kept losing radio reception even at close range. Need to fit the satellite receiver in the nav cabin methinks.

This is the fifth of the six sisters of the isle of Man Steam Packet Company, entered service in 1952 and scrapped in 1980. it is built on a Metcalf Models hull, and the superstructure is scratch-built from styrene. Fittings are a mix of scratch and purchased. it is powered by 2 Electronize motors with 2 ESC's by EA Electronics, has a smoke unit from Harbor Models controlled by a Viper ESC, a sound system from Model Sounds inc of Ontario, and powered by NiMH batteries. it is also fitted with a working bow rudder and lights, all controlled from a Robbe F14 Navy radio fitted with 2 twin sticks. Preferred sailing location is Lake Lisgar in Tillsonburg, Ontario.

here are my three boats, oakgarth 42" twin screw 4 blade props with kort nozzles she also has a working bow thruster.She running two speed controllers off a 12volt sla battery and has full working lights I would love to say I built her but I never, all I have done is added lights and give her a full makeover. Next is Doug the26" pusher tug twin screw 3 blade props full working lights and water jet single speed controller futaba radio set up I have just changed the crane on this again I have only done cosmetics to this tug and my last boat is a 20" seaport tug this is what my grandchildren sail and for 60 quid its great thay love it .the paddling pool was 15 quid for argos and perfect for testing well better than filling the bath .

London tug boat. 1:32 12v engine. Radio Futaba 7c. Lights and radar.

This boat is scratch built on a Fiberglass Hull. The Lily was one of two ferries built in 1900. Her sister ship was the Rose.
The superstructure of the model is largely light-ply and paneled to resemble the orginal. She had an open top deck and as you can see the navigation pods were open to the weather.
A semaphore signal arm was included as radio was not yet used to communicate with each other on the Mersey.
The model is approx1/48 scale and built from a couple of photos and sketches that exist. She is powered by two 340 electric motors and controlled with 2.4ghz radio. A 12 volt battery gives the power. Both decks are individually planked.
She has sailed at Hoylake.

A scratch built model of a Gloucester USA fishing schooner 1900 era. Pine plank on frame, 2 channel radio with a Lego 9volt drive unit as sail winch controlled each way by servo and micro switches, the deck is planked on a thin ply sub-deck and deck openings are sealed with Vaseline. The deep keel slides up into a box through the keel and secured with a bolt.

Scratch built 1/48 scale Mersey ferry Snowdrop in current use on the Mersey (ex Woodchurch)
Model interiors fitted out with tables chairs people etc and 72 leds light to Illuminate the interior saloons.
Just completed and maiden voyage on Hoylake Lake on the Wirral.
2.4Ghz radio and a bilge pump just in case. Sails a treat with 100 passengers. Extensive use of plasticard on superstructure. Fibreglass hull from own mould.
See sailing location at www.hoylakemodelboatclub.co.uk
Our club can supply the hull if you want to have a go at building one.

💀 Hello friends, I am sharing a kit that sells here in Brazil. This is a fishing boat, a motor included in the kit 380 brushed, propeller shaft, pipes, all made of balsa. To put my touch to the lighting, did the radio antenna, put some flags. Detail is left with the box of fish that are rice painted with spray paint aluminum.

Single 550 Brushed Motor and Reversible ESC, 2S LiPo, 2.4GHz Radio System, Turnigy Blue Prop, 2 x 9G servos for rudder and lights.

Functional Nav Lights and wailing siren.

OA Length 690 mm, Beam 180 mm, AUW 1656 grams.