This video shows four New Zealand frigate models, at 1/48 scale, radio-controlled, HMNZS Canterbury leads, then Waikato, Otago and Taranaki. All models built from scratch, from Navy plans.
Build time about 6 months each. 1970's era idea based on a photo of these ships taken sailing in Wellington Harbour.
This boat was pulled up from our local pond by one of the fishermen .No one has a clue how long it has been down there but must have been a very long time .So I was set a challenge to sort it out I got one of the servos working and the speed controller working OK just shows no matter how long something has been under water it can work.
I did get the motor running but as you see not wise to use.So I have put some pics on of my progress up to now to have a look at.
A few pics of my partly scratch build RTTL from Kitshack. Picked this up from Ebay as a first kit.
Has a few printed balsa hullparts but lots of templates to cut out. Plans also show lots of topside details.
Powered orignally by 2 MFA 500's and 2 7.2 NiMH with 35mm props, OK but run time poor.
Complete change, 2 400's and downsized to 25mm props, much better run time and good on the plane.
Next upgrade is to LiPo batteries.
Next build is likely to be an Aerokits Sea Hornet or Sea Breeze.
Really fine looking model. The detail really adds to the finished model.
Glad to hear you have chosen to go for smaller motors and props. The weight saving will really have improved the performance, and LiPos will make it sparkle. if your ESC(s) do not have some sort of cut off for low volts I suggest you fit a warning device to the LiPo to prevent over discharge.
Be good to see the model running on the water!
Dave 😀
Indeed Dave, charger, batteries, alarms and charging bag on order!!
Sadly although my ESC's (tamiya TBLE02's) are Lipo compatible research says their cut off limit may be too low so fitting the alarms too as a fail safe.
hoping to get some video once its running consistently.
Finally managed to put a little film together of my 1.24 Grey Goose taken at the Herne bay regatta. As well as the usual turning guns, lights and ship sounds this boat fires working torpedo's using a CO2 gas system. Will be putting some film of this on youtube shortly.
If your interested I'll be exhibiting at the Southern Model show this weekend and will demonstrate the torpedo system at the show. Hope to see you there.
Following burning out the motor by fouling the prop on a polythene bread wrapper I fitted a new 160 amp speed controller and got a bargain motor from Giant Shark. it is an Emax GT4020 which cost about £14. I realised what a bargain it was and went back only to find Giant Shark have ceased trading. The video shows the boat running on a 4 cell Lipo, it goes a bit quicker on a 5 cell that I have. I am really sold on Lipo power as Dave said I would be. I have just ordered a 3 cell Lipo for my crash tender
Ahoy
Here is a display model I built it is the late great RMS LUSITANIA scale 1/350 built for show only it took me 7 months to build a one of a kind kit something you don't see everyday built from a kit mostly scratch built did not like some of the kit parts so I made my own.
complete scratch built on a glass fibre hull here are a few more photos to show the progress that has been made still a lot of work to do boat powered by a540 motor driving a 60mm 3 bladed prop I sail at pickie pool in bangor co down Robert waterson angus
alan the hull is fibre glass scale model of new venture moulded by bill wood for me she is same scale and design as my own fishing boat was built early 70s all the rest is totally scratch built from my original drawings glad you like it winch lights radar all wired up and working I hope to give it arun out on next sunday morning allgoing well will put some pictures on afterwards rgds r w angus
This was the 1-35 scale plastic model kit and converted to RC 3 props 2 working port and the starboard the centre is non running. Due to weight I used a 11.7 lipoly battery so it's fast but the running time is only about 20 30 mins
It won best in show in the navy boat section at our club due to the detail and the figures so can't be bad
this is my latest project just got running gear in boat is fully wired main deck sealedworking trawl winch made wheelhouse and hatch just sitting in position bulwark frames allin and trimmed one photo shows finished boat ahc waterson b444 skiboo this boat is all scratch built going to be finished rigged as a trawler scalloper on a fibre glass hull by bill wood
Robert waterson angus
Here's a few more pics showing my home made winch from a Lego 9volt motor unit which is controlled by a servo and two micro switches. There's a ring on the deck line that all the sail lines are tied onto. Cheers Lubber. PS. The large mainsail is counter ballanced by the deep hull shape right aft. Regards.
New 1/48th scale Diana and Huntsman plus anew Club Racer
Knightcote Model Boat Club. Film is of boats David Pledge and I have developed -- to be sold as kits soon. The Diana and Huntsman are tiny and powered by micro brushless motors. CR1700 is a new brushless club racer. See us at the Warwick show this week!
Hello from Australia Thought it was time I made a an effort. Three of my models shown here at last years local model show in Port Macquarie. L to R they are Cervia,now 20 years old,Wyola, an Australian built tug.Twin motors and Kort nozzles.and Old Trafford, MSC paddle tuc in 1/35 scale. All are totally scratch built. The only things bought were materials,paint and glue, Except the stantions for Old Trafford. Currenly finishing a Maycraft Mercury(started in 1962 in England) and a Vosper fireboat.Hope this may be of interest
👍