Miss Katherine runs very well though the geared motor linkage is a bit noisy, needed some grease.

Here is the real Miss Katherine as you will find her today should you visit Mahone Bay, Nova Scotia. She has been in the boat yard for over 15 years.

It was from these photos that the model was created by me.

Ron Bauer

This is a Dumas kit for a USCG Life boat 44' built in Curtis Bay Maryland Coast Guard yard. I've been working off and on this model for a couple of years.

Krick WSP 47 as seen on MBW vids

Working radar and blues (no twos..... yet)

This fantastic model was scratch built by John of the Solent Radio Controlled Model Boat Club. Here it is seen sailing in light winds on Setley Pond in the New Forest, UK.

She took about a year to construct and is now into the third year of sailing. The boat is based on the period 1929/34 when "Bobby" Somerset owned her, he won the Fastnet race twice and finished second once, infact she is the only boat to win the Fastnet three times. She is based on the river Hamble and is owned by Dauntseys school in Wiltshire and is regularly raced by the pupils there. The model is approximately 1:15 scale.

In 2013 the full size Jolie Brise celebrated the centenary anniversary of her construction by the Paumelle yard in Le Havre in 1913. The world famous, gaff-rigged pilot cutter was the last boat to carry the royal mail under sail and has won the Fastnet Race three times, including the inaugural race in 1925. in 2015 and 2016 she was the overall winner of the Tall Ships Races.

Jolie Brise is owned, maintained and sailed by the pupils of Dauntsey's School. For more information about Jolie Brise go to,
www.joliebrise.com

(apologies...just seen this vid was already posted by Dave M😁)

This is the 29" Brushless Miss Geico. Running on two 14.8 volt 5000mAh LiPo batteries. in Herbert Woods Boatyard in Potter Heigham Norfolk. She is pretty quick but do not know her top speed. Turns flat out on full rudder lock. Runs for about 15 to 20 minutes. Would recommend as a great fun boat.

Top Boat is the City of ELY after the II world war, with guns removed.

Bottom Boat is the SS JOHN W Brown partly rebuilt to wartime structure.
Class: EC2-S-C1 Type Liberty Ship
Launched: September 7, 1942
At: Bethlehem-Fairfield Shipyard, Baltimore, Maryland

Length: 441 feet, 6 inches
Beam:57 feet
Draft: 27 feet, 9 inches
Displacement: 14,245 tons
Gross: 7,176 tons
Capacity: 8,500 long tons
Armament: Three 3-inch/50 caliber guns; one 5-inch/38 caliber gun; eight 20mm guns.

Built from a .PDF plan I found on the net, this 22" Outrigger Hydro sports a Hobbywing 3600Kv Brushless, along with a Hobbywing 60A esc, a 5000mAh 11.1v 45C LiPo, and an Octura X435 Prop connected to a Strudder from Prestwich models.. it weighs 930g without the battery, with the battery, she goes 1386g.
This was it's Maiden run, at Herbert Woods Boatyard, at Potter Heigham Norfolk. it ran very nicely, but can do with a little tweaking to get more speed.
For the record, I did not swear, it was someone onlooking.

HI fellow modellers, Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was scratch built using a fibre glass hull and plan obtained from a fellow modeller at the Bridgend Show in 2007. The front door and some fittings are made from plastic card and tube, decks are from ply and timber. On board figures are from the pound shop and car boot sales, modified by myself. The on board tank and half truck are RTR models that I have modified their looks to fit into a WWII theme for the craft. This craft has twin drive, 400 motors via 2.5/1 gearboxes. I tend to use both sticks on the TX for drive as this allows me to turn the model on a six pence.The dispatch door works from a rotary pot on the TX and via a rotary sail winch servo in the hull. I have just modified my Planet 5 TX to allow me to change my radio gear in this craft. This model has had meny trips on Cwmbran Boating Lake and at shows the society attend during the year. Still haven't allowed the tank or half track to run off the landing craft up the lake side slipway. one day I might get it on video. Hope you enjoyed the photo's. Regards GreyWolf

HI Fellow Modellers,
Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was built from a Caldercraft Kit, This model came into my possession for the price of 20p, a raffle prize at Bryn Bach Model Clubs OPen Day 2010, when it was built is unknown. The item being made for display use and not finished off, no internal electronic fixtures. Did have a prop shaft and prop that had not been fitted correctly. 50% of all the fixtures had to be removed and refitted before they fell off, some didn't stay in place from the show back home. The model was finised off using a photo of the Milford star on the internet. The fish boxes and figures being obtained off DON one of the Society members who had a mould to make them in white metal, only required cleaning up and finishing off. A graupner 6 volt steam unit is fitted in the funnel and to make the boat a little more realistic on the water,a maplin steam sound system has been used to generate the sound of the engine. A simple mod allows the revs to be linked to the engine voltage. The drive motor is a 550 with the lowest revs I had in MJB's this was married up to a 2.5/1 gearbox I also had in stock. The main motor and steam unit are supplied from a 7.2 volt nicad racing pack. This model has had meny fishing trips on Cwmbran Boating Lake and at shows the Society visit. Hope you enjoy the pictures, Regards GreyWolf.

HI fellow Modellers,
Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was built using a Billings Kit, bought for me as a Christmas pressent in 2009. A graupner 6 volt steam unit is fitted in the funnel and to make the boat a little more realistic a maplin steam sound system has been used to generate the sound of the engine. A simple mod allows the revs to be linked to the engine voltage. The steam engine rotates using a stripped down minI servo, fitted under the motor housing on the deck, again linked to the main motor voltage. The two 9.6 volt AA batteries and control gear are mounted under the boats floor, forward locker, a minI servo for steerage is fitted under the rear seat and the receiver is located under the wood pile. Figures are self made from items obtained from the local pound shop. The modal can be seen sailing at Cwmbran Boating Lake or at shows the society visit. Hope you enjoy the pictures, Regards GreyWolf.

HI to all you Fire Boaters,
I have decided to finally bring my Fireboat out of the closet and up for inspection.
This is the first of my many boats I am showing, I will probably show others in the future.
I started to build her back in 2006 after being off work and having a shoulder operation. She was not going to be a R/C boat, just a bit of something to do whilst on recovery.

I have a 34" still in the box unmade, purchased back in 1994 from Aerokits.
I drew round all the parts and then shrunk them on my scanner. She is 27" long I think that's
just fraction over 1/20th scale . She is almost all balsa except the 2 under skins that are balsa laminated with 1/64th ply. The hand rails are 1/4" balsa blocks I cut from a strip and the rail is ally tubing.
The mast is made from plastic strip from packets from the model shop.

When I returned to work she was put into the shed and left unfinished.
I stumbled across the Fireboat website and registered in 2009 when I was off work once again. This then made me think more about working on her again and I decide to turn her into an R/C model. So out she came and I fitted an Electomax Delta 480bb motor and a M3sonik esc.
I also purchased a couple of Robbe fire monitors, put them together shortening the nozzles and cutting the bottom of the base of to try to look a bit moreto scale. I know they are not the correct type but if I want to go down the road of getting them working then these ones will.

Then off I went to Wilkinson's and bought some paint. Then set out to paint her, as I brushed on the paint it seemed to be drying almost as quick as I was painting her. Dragging the paint I had just put on with next brush stroke. What a TOTAL DISASTER !!. I gave up on her and back into the shed she went.

2010 arrived I started again rubbed the paint down a bit and bought some Tamiya spray acrylic and started spraying, underside red, it seemed look all right. I used a nice new roll of low tack masking tape, taped up the underside and the decking and sprayed on the black on the sides. I thought that look all right. Took off the masking tape, which also took off the red paint and the dope from the decks. Another DISASTER. Back in the shed she went once again.

A couple of months went by and I was up in Norfolk on my own boat and watching the workers in the boatyard, ideas came to me and when we returned home, out she came and I repainted the sides
and then with red oxide paint I painted her undersides to make it look like antI foul paint. I used some white stripe to cover the join of the two different paint colours.
I had bought some roundels in Anglia Model Shop in Gorleston and some lettering in a shop in Norwich and after painting put these on.
Not looking fantastic but passable I was a little happier with her, but still not satisfied, back in the shed she went again.

Now after so much nagging from my brother out she has come, I've started again. He talked me into changing and trying a brushless motor and a smaller esc he had in his tool box from his helicopter he was shelving as its rota head was damaged beyond repair.
I have now fitted them and if they work I will change the esc to a forward/ reverse esc in the future at some point.

Sea trials are still away off more than likely in the spring, because the decking has yet to be painted. That will be the next job.

I think that's all for now, as I have probably bored you all to tears. I hope update as I progress further.
Just to let you know I'm Tom (alias BOATSHED).