I thought as the lake is still full of weed this would keep me sailing built from light ply fibre glassed inside & out then painted length 33" width 12"height 16" to top of the prop
70 amp esc aircraft brushless motor 11" prop

I am busy with a landing craft i thought this would be another one to beat the dreaded weed 😱

HMS Victorious,circa 1941.
Still very much in the early stages of construction.
Most of the internal workings are in place ,but still a few ideas to work on.
Thus far she has a working forward aircraft lift.
A smoke generator (water not oil).
All four rear guns rotate.
A working bilge pump.
Working next on how to activate the crane.
All three engines are powered from a 6 volt battery.
All other items mentioned above powered from another 6 volt battery,bot of which provide the main ballast.
As I say still a long way to go yet as can be seen.Many of the fittings have to be more authentically painted.

PT 109 was one of the hundreds of motor torpedo boats (PT) of the PT 103 class completed between 1942 and 1945 by Elco Naval Division of Electric Boat Company at Bayonne, New Jersey. The Elco boats were the largest in size of the three types of PT boats built for U.S. use during World War II. Wooden-hulled, 80 feet long with a 20-foot, 8-inch beam, the Elco PT boats had three 12-cylinder Packard gasoline engines generating a total of 4,500 horsepower for a designed speed of 41 knots. With accommodations for 3 officers and 14 men, the crew varied from 12 to 14. its full-load displacement was 56 tons. Early Elco boats had two 20mm guns, four .50-caliber machine guns, and two or four 21-inch torpedo tubes. Some of them carried depth charges or mine racks. Later boats mounted one 40mm gun and four torpedo launching racks. Many boats received ad-hoc refits at advanced bases, mounting such light guns as Army Air Forces 37mm aircraft guns and even Japanese 23mm guns. Some PTs later received rocket launchers.

This Proboat PT 109 model was brought in 2013 for £100 these boats are rare now, This one had a few faults with the propshafts they were bent and noisy both were replaced, with quality 4mm shafts, motors twin 600s were also replaced by Graupner versions along with mounts and couplings, basically all the running gear, also two ESCs by Aquapower were added and a 2.4G RC system.

This is Brian Clewes Hovercraft on a frozen Boundary Park Lake in Cheshire UK.
Our resident cob swan and his wife were sat on the ice probably hoping we had brought some feed. They don't bother us and we leave them alone. I should have filmed them taking off later, not an easy task on ice for one of our largest birds.
The hovercraft has two brushless motors and uses a LiPo.

One of my favourite RC shows of the year. The Southern Model Show has a bit of everything. The temporary boating pond is used by about 6 clubs who demonstrate their various watercraft to the appreciation of the visiting public.

So, here's my current project in the works. I got a nice 25-inches Deep-Vee fiberglass hull a while ago and now (finally) have a concept for it. Almost by accident I came across a plan for an American bass boat which in turn reminded me of a boat that caught my attention when I was a kid while reading a boating magazine. The boat is a 28-footer from a now defunct firm named Uniflite. it was a small deep-sea sports fisherman called "Salty Dog". Uniflite was very well known within the American boating circles during the 60s, 70s, and 80s. Uniflite created and supplied PBR river patrol craft to the US Navy between 1965 and 1972 for rivers in Vietnam using an already existing pleasure boat hull and adapting jet nozzles for propulsion. So, I just created a prototype template of the cabin so more to follow 😎.

22.5 inches RC boat inspired on 1970s Chris-Craft Commander 36, 42 and 45 footer boats. Model equivalent to a real-life 36 footer vessel. Barebones fiberglass hull from a UK manufacturer. Powered with a brushed 500 motor, 30A controller, 9.6v NIHM battery. Video made during first trial at the Eibsee lake in Bavaria, Germany.

I have just completed my Puffer and am quite pleased with the outcome. The components are quite good but do need a bit of fettling but this is what our hobby is about. This is my third Caldercraft build so I am used to their quality and sparse instructions.   As usual for Caldercraft you need to have your thinking cap on as the A0 plan and the 'instruction book' do not match up but of course they do expect you to have a little bit of experience in model building. it has taken me about 6 months to build working on and off over this time. it has a large hull which is easy to house the motor, ESC, RC and batteries, etc. (I installed 2 lead acid 6 volt batteries, one on each side amidships) which gives stability and ballast. Being a large deep hull it needs a lot of ballast, even in its short length.I have only tested her in the big white nautical test facility at home so do not know how it will perform on our lake but hope to try it out on Sunday if the weather is set fair. Tried her out Wednesday and she sailed really well - maybe a little more ballast in the bow but not too concerned.

Found this Dense block of foam, floating in local Ashton Canal, whilst sailing other boats with my brother, whilst rescue a stuck boat from the reeds, in 1996 was temporarily on the dole at the time, struck by her Landing craft shape on turning it over plus realised I could carve it like wood, later using my bits box, after carving a couple of box shaped groves, for battery, motors and rc equipment, literal rammed a prop shaft, and rudder shaft through hull, and fashioned some balsa sheet into superstructure suitable camouflaged , I had a "US Army Vietnamese River Craft" of sorts and with its 1 1/2 to 2" thick Hull virtually unsinkable, hence its name :-). Here she is in 2000 sailing at Ethrow Park. May in the future alter her superstructure, she makes a handy towing barge for both mine and my brothers Tug Boats, and if rc left connected can even act as rescue boat if they pack up or get weeded up :-) - Have delete this from You Tube and replaced with slightly clearer version, but it seems to be still working here mysteriously, may cease working eventually, new version above :-)

Although not strictly speaking a boat it is a yacht and fun when you can't get to the pond but fancy a sail!

Built from magazine free plans mainly of balsa, carbon mast and drafting film it is just as challenging as normal RC sailing.

Operated on a 2CH Rc is has front wheel steering. The wheels are model aircraft wheels. The rear outrigger wheels and mast can easily be dsmantled for transportation. The outrigger is also ballasted to Improve handling.

This is a 40" long model of a gas powered Berkley Company kit of a US Air Force crash boat from 1955. The plank on frame kit was in production for about 10 years and was meant to be powered by a model airplane gas motor with a single shaft. it depicts an experimental 50 knot rescue boat (painted in a peace time color scheme) during service with the USAF. if successfull it would have been put into production designed to be a replacement rescue craft for all Air Force 65' crash boats. Unfortunately for the crash boat program the Air Force lost interest as helicopters were become a reliable way of rescueing downed pilots along the coast. The prototype and a sister boat were scrapped, as was the entire program.
The model was given to me to be restored(top picture) for the son of a retired USAF veteran that was a crash boat crewman. The model was built in 1957 and had been run a few times on a tether line, R/C was pretty expensive back in the day. I stripped the hull, filled in all the cracks and rebuilt the mast. I added a small boat, davit, liferaft, coxswain station, spray shield and deck hardware among other things. Actually all the owner wanted was a paint job, he was very happy with it's new appearencep! Although I fiberglassed the wooden hull and made it watertight, the owner doesn't plan to run it, just a memorial to his dad's service. I really enjoyed working on this "rare bird".

MY OWN DESIGN HOVERCRAFT & SKIRT FILM ON LOCATION AT GARLIESTON SCOTLAND, 10 inc THREE BLADE PROP, OUTRUNNER MOTOR, 12 VOLT LIPO BATTERIES.