A test post on behalf of redpmg.
The engines are built by a mate of his.
"The boats are built by a 90+ year old gent by the name of Alan Raubenheimer, who used to make Rose Pop Pop Boats - used to advertise in MB etc.
Now into his 90s he has finally given up production."
Here goes🤞
Doug
It woiks 😊; just ignore the 'Invalid file' notice and click the blue magnifying glass and then the download button.
Run with Windows Media Player.
When it opens Press F11 for full screen or drag a corner with the cursor to enlarge.
Resolution is not too good I'm afraid🤔
Despite the music the action takes place in SA not Hawaii!😉

PS 8.5.20. Video fixed and enhanced a little 😀😎

last pictures l posted l painted the wave princess l changed my mind and decided to go for some planking on the decks and cabin roofs l have also done a little bit of tarting up using some brass welding rod and brass tube l am quite pleased with the out come so far. these piccys are about a month old now so she has had a god rub down and given six coats of clear varnish. l will post more piccys when l have installed the windows and frames.

made from a krick felix launch kit.As usual i have made slight changes especially in regards to the final finish of medium oak stain.
The original windows were cut from a sheet using templates provided and some did not fit as they were on the small side.i used some plastic sheet i had to make my own replacements.I also changed the prop coupling for a universal joint(i always do)
I prefer the less is more approach to some models.

Brought this vintage Aero Kits RAF Crash Tender for £50 from Newcastle area, it is the 34in version.
To my surprise at home I found that it had a Bullet 30 motor installed these motors were the top drawer motor of early fast electrics in the early 1980's and its the only one I've ever seen, it can run on 24v and pull around 15A giving 300w not bad for a brushed motor.
due to the power of this motor I have modified the hull under the water line with turn fins and trim tabs to reduce torque roll and improve turning stability, the underside is incorrect already as it only has one propshaft, where the original had two and I believe that both props turned in the same direction.

The Pictures here show some of the work in progress I have remounted the motor and added a speed controller rated at 24v
I have remade the stern compartment and rudder gear under it.
I have blocked windows and foamed the front half of the boat.
made missing parts and repaired delaminating ply.

Note old ply is not as good as modern, the glue is not as water resistant.

Have painted the hull and have just ordered the decals from Cornwall model Boats :-https://www.cornwallmodelboats.co.uk/cgi-bin/sh000001.pl?WD=hose%20fire&PN=becc_fire_tender%2ehtml#aB_2dFTS1_2e32

The 34in is 1/16 scale

Fitting can be brought but many are cast white metal and can add weight to the boat, I have made two water cannons and plan to buy plastic fittings from this site.

This has turned out to be a task that is difficult to assess how much effort and money to spend on a hull that has been built by someone else (say no more).
Have just finished the steps for the stern compartment.
Painted and now for the test run.
the Bullet 30 motor ran well between 14 and 18v,

after sellotaping the windows and fitting new electrics it went better !!!

Gordon bought this hydro from Ebay and fiddled with it lots to get it going. So we went to Ilfracombe pond for a test. it went jolly well to begin with until a large input of water through the windows made it unstable and the result you can see !!! After we recovered it and dried it out it went lovely as you will see from a later video. Les Breame

Since my last posting I have spent weeks stripping the paint, refilling where required and have had to make new roof and floor sections, worst part has been been the front windows as these were totally rotten once the old paint was removed, and making new ones was hard because the old frames they attach to is warped. I still have not fitted them yet as I'm looking to paint and glaze first.

Bought off ebay, where else! Had been started as a cruiser, with one very small electric motor,then put in a loft for goodness knows how many years.Replaced prop shaft with 2, 40mm r/h and l/h props, 2x 540 motors running through 40a esc.Radio is 27mhz. 2ch. would like to swap to 2ghz to get rid of the unsightly aerial! I am awaiting some plasticard windows to Improve the looks and will slowly add fittings as and when.I tend to sail it every now and again on the boating lake in BUXTON, no-one has shouted as yet,though I'm not sure the swans approve.!: The photo on the water was just as the power was running down, none as yet at speed.It is very manoeverable with the twin rudders,almost on the gunwhales at speed.

HI all, I was given this model in a rather sad state as it had been in a junk box in a farm out-building and had been subjected to the weather from time to time . it had been there for about 20 yrs or more and the balsa hull was 60% rotten . I think it was originally IC powered but had been fitted with a Graupner Jumbo 6v motor and an old style rheostatic sc, ( I did try using the sc but it sucked so much power I gave it a miss - also had no reverse)
Amazingly the motor and sc still worked and with a bit of oil and cleaning the motor is still running well ! I'm using a 1975 Futaba 24v 10A sc and 3cell LiPo which pushes it along nicely. I stripped everything and replaced large bits of the hull, (which was fun as every time you picked it up you would poke another hole in it it was so fragile !) I got it to the stage where it would hang together fairly well and glassed the hull which has made it like the proverbial "brick one". The rest was very careful sanding of the deck and cabin, (they were ply so fared a bit better) and a lot of little filling bits to get it right.
Nav lights and cabin lights all work from the micro switch board, the curtains are left over Graupner Commodore (1975), I've added a mast, new windows,flag pole, cleats, ladder and handrails. Any ideas as to its manufacturer would be great. I have seen another one on our local "Trade Me" web site recently.

installed motor,radio gear and 15amp vipor controller,windows hand made mast and fittings

HI fellow model boat people,just a couple of photos showing a rescued aerokits sea queen circa late 50s.
This was in poor condition, work was started mid January to strip down the various parts that required to be remade, deck/superstructure/roof panels/windows etc.
The hull needed stripping back to give a good surface for the finished paint work.
Completion of the basic boat is now getting near, and ready for fitting out with motor radio etc.
Hope to give more details later.
Cheers for now.

For my first foray into boats I have acquired what is like a Vosper Firefloat Mk.2 but it is different. The wheel house section of my boat is different, being longer, the mid-ship section having three windows in lieu of two and the stern is completely different in profile.

I have spent many nights trawling the internet to see if there is anything like my very detailed model but to no avail and I have even asked a few of my old work colleagues who are ex-naval men if they can help out in identification. I am wondering whether this could be an elusive Mk. 1 - the boat that was never put into commission.

I attach a few photos of my model in the hope that someone out there can throw some light on it. it is in very good condition and a few years old, is fitted with a Graupner Eco 600 motor on a single prop with 7.2 NiMh batteries. it is about 34" in length and 9" beam and goes really well, planes quickly and turns very tightly - in all a cracking boat. The numbers on the side of the boat are strange as they relate to what I believe is a coastal command unit - the numbers are not new as they appear to be original under the paintwork. Any help in identifying what actual boat it is modelled on would be appreciated.

Regards
Alan