Bought off ebay, where else! Had been started as a cruiser, with one very small electric motor,then put in a loft for goodness knows how many years.Replaced prop shaft with 2, 40mm r/h and l/h props, 2x 540 motors running through 40a esc.Radio is 27mhz. 2ch. would like to swap to 2ghz to get rid of the unsightly aerial! I am awaiting some plasticard windows to Improve the looks and will slowly add fittings as and when.I tend to sail it every now and again on the boating lake in BUXTON, no-one has shouted as yet,though I'm not sure the swans approve.!: The photo on the water was just as the power was running down, none as yet at speed.It is very manoeverable with the twin rudders,almost on the gunwhales at speed.

HI fellow modellers, Another model from the RADMC fleet at the fleetshaven workshop and boat yard in Ponthir.This model was scratch built using a fibre glass hull and plan obtained from a fellow modeller at the Bridgend Show in 2007. The front door and some fittings are made from plastic card and tube, decks are from ply and timber. On board figures are from the pound shop and car boot sales, modified by myself. The on board tank and half truck are RTR models that I have modified their looks to fit into a WWII theme for the craft. This craft has twin drive, 400 motors via 2.5/1 gearboxes. I tend to use both sticks on the TX for drive as this allows me to turn the model on a six pence.The dispatch door works from a rotary pot on the TX and via a rotary sail winch servo in the hull. I have just modified my Planet 5 TX to allow me to change my radio gear in this craft. This model has had meny trips on Cwmbran Boating Lake and at shows the society attend during the year. Still haven't allowed the tank or half track to run off the landing craft up the lake side slipway. one day I might get it on video. Hope you enjoyed the photo's. Regards GreyWolf

Have had this boat 30 years .Started it for my eldest son but never finished. But now with two boys of his own I am determined to give it my best shot.
Completly stripped it, repaired delaminated sections,took out all the gear (motor,radio,servos) and started again.
I will update progress as time goes on but I am determined this will be on the water this year.

Built from Aerokits kit originally but rebuilt/modified many times since then!
Twin 540's (geared) 6V Pb Gel battery for drive. 3 Blade 50mm props (contra rotating) lights (cabin, running Ights and searchlight) on 4.5V Deacs. radar scanner and winch on same supply, radar display screen on a single AA 1.5V.

Fleet Systems radio and speed controllers, Futaba rudders servo, RCME servo driving cam/micro switch unit for lights etc.

A quick ( 3 weeks) rough 35" balsa MaiamI powered by Turrnigy 28/30 outrunner , 3cell LiPo and 30A ESC made for my son who wasn't that interested so I am adding a bit more to it and 'playing' with it myself .
Vic Smeed plan Thornycroft took about 20yrs (on and off) to complete and has an Electronize 43HX 24v 15A controller, 2x 400 sized 6-12v brushed motors 4cell 3000MAh LiPo for main power with seperate 3 cell LiPo running a computer fan for cooling (fan is linear and sucks air through the boat from the front hatches and blows it out through the rear hatches) There are also seperate 3 and 4 cell AA NmH packs for nav and interior lighting.
Boat runs 28mm 3 blade props and runs at a realistic scale speed and attitude. Radio gear is 2.4 and I have modified one TX for twin throttles and at present am running both these boats simultaniously on the one TX.
Have bought twin car ESCs, batts, RXs and BECs for the PT and the (36") British Power Boat 64ft HSL I am building (modelled on the RNZAFs 64ft HSL- the only one sold in the southern hemisphere - in 1940) Went on board as a teenager before she was ruined by being turned into a pleasure launch so it was a help with the building. Still remember the wonderful alloy 'Power Boat' stair treads down to the ward room. Will get some pics up of the HSL as well.

installed motor,radio gear and 15amp vipor controller,windows hand made mast and fittings

I have admired this design for many years, along with a lot of Vic Smeed's drawings.
This model is enlarged by 1.7 giving a length of 36'' and a scale of 1:16. The finished boat weighs about 15 1/2lbs and is powered by an MFA 919D 540 with 2.5:1 reduction, using an Mtroniks ESC and Planet 2.4ghz radio.
The hull was planked in obeche on 6mm ply keel and frames with mahogany blocks at bow and stern. The photos were taken on her maiden voyage at Crealy in Exeter.

Here is my video of the Sterling American Scout, Under way for the first time in 50 years. Powered by a dumas 6 volt electric motor and a 1957 Babcock citizenship all tube radio. the predisessor of RC.

Ahoy
Here is my vintage 1958 Sterling American Scout Runs on a old Babcock citizenship all tube radio. the great great grandfather of RC as we know today. all those years and it still works. I was 18 years old when I built this kit. I have a underway video to go along with post. Boats

first time on the water for my latest build, 23" model of british power boat co. 68ft type 3 hants and dorset raf high speed launch,
power is speed 400 driving 35mm three bladed prop, 7.2volt 3300mha nimh planet 2.4 ghz radio,
scratch built, I used scaled down drawings from my aerokits plans then gave the frames more shape to replicate the curves of this boat, the forward section where diaganally planked.
then sides and bottm as normal with sheet ply, deck is teak planks.
I sail on the rotary pool at penzance.

Here are a couple pictures of my 1957 SS AMERICAN SCOUT C2 Merchantman. powered with a dumas 6 volt superpanther electricmotor, For RC opperation the ship is radioed by a 1960 babcock citizenship tube radio atae of the art at that time nowdays it is a relic or dinosour. BUtttttttt it still works. I am going to take her out for thefirst time underway sail scince 1960 I will update this post with pictures of her underway. But here are a couple stil pictures of her. Thanks fellas for your viewing my Freighter.

HI fellow model boat people,just a couple of photos showing a rescued aerokits sea queen circa late 50s.
This was in poor condition, work was started mid January to strip down the various parts that required to be remade, deck/superstructure/roof panels/windows etc.
The hull needed stripping back to give a good surface for the finished paint work.
Completion of the basic boat is now getting near, and ready for fitting out with motor radio etc.
Hope to give more details later.
Cheers for now.